Ultrafuse ASA @XL 0.6

Forward AM · ASA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*ABSC*

→

Ultrafuse ABS

→

Ultrafuse ABS Fusion+

→

Ultrafuse ASA

→

Ultrafuse ASA @XL

→

Ultrafuse ASA @XL 0.6

Includes (3)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Settings

Basic information

Material variant: ASA inherited
Vendor: Forward AM inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.07 inherited

Print temperature

Nozzle (initial layer) (°C): 270 inherited
Nozzle (other layers) (°C): 265 overridden
was 270 (inherited)

Cooling

Fan minimum (%): 15 inherited
Fan maximum (%): 40 inherited
Disable fan for first N layers: 4 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 0.98 inherited
Max volumetric speed (mm³/s): 9 overridden
was 5 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	105 inherited	105 inherited

Other settings

bridge fan speed: 100 inherited
compatible printers condition: printer_model=~/.*XL.*/ and nozzle_diameter[0]==0.6 and printer_notes!~/.*HF_NOZZLE.*/ via *ABS06XL*
cooling: 1 inherited
cooling perimeter transition distance: 10 via *ABS06XL*
cooling slowdown logic: consistent_surface via *ABS06XL*
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 0 inherited
filament colour: #FFF4CA inherited
filament cooling final speed: 2.5 via *ABSPG*
filament cooling initial speed: 5 via *ABSPG*
filament cooling moves: 3 via *ABSPG*
filament infill max crossing speed: 140 via *ABSPG*
filament infill max speed: 0 via *ABSPG*
filament load time: 10.5 via *ABSPG*
filament loading speed: 10 via *ABSPG*
filament loading speed start: 50 via *ABSPG*
filament minimal purge on wipe tower: 35 via *ABS06XL*
filament multitool ramming: 1 via *ABS06XL*
filament multitool ramming flow: 40 via *ABS06XL*
filament multitool ramming volume: 5 via *ABS06XL*
filament notes: Material Description Ultrafuse ASA is a high-performance thermoplastic with similar mechanical properties as ABS. ASA offers additional benefits such as high outdoor weather resistance. The UV resistance, toughness, and rigidity make it an ideal material to 3D-print outdoor fixtures and appliances without losing its properties or color. When also taking into account the high heat resistance and high chemical resistance, this filament is a good choice for many types of applications. Printing Recommendations: Apply Magigoo PC, 3D lac or Dimafix to a clean build plate to improve adhesion. inherited
filament ramming parameters: 250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387 via *ABSPG*
filament retract before travel: 2 inherited
filament retract layer change: 0 inherited
filament retract length toolchange: 20 via *ABS06XL*
filament retract lift: 0 inherited
filament soluble: 0 inherited
filament stamping distance: 45 via *ABSPG*
filament stamping loading speed: 26.5 via *ABSPG*
filament toolchange delay: 0 via *ABSPG*
filament travel max lift: 1.5 via *ABS06XL*
filament travel ramping lift: 1 via *ABS06XL*
filament travel slope: 1 via *ABS06XL*
filament unload time: 8.5 via *ABSPG*
filament unloading speed: 60 via *ABSPG*
filament unloading speed start: 60 via *ABSPG*
filament wipe: nil inherited
idle temperature: 100 via *ABSPG*
renamed from: Ultrafuse ASA @PG 0.6 overridden
was Ultrafuse ASA @PG (inherited)
start filament gcode: {if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/} M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.04{elsif nozzle_diameter[filament_extruder_id]==0.25}0.1{elsif nozzle_diameter[filament_extruder_id]==0.3}0.06{elsif nozzle_diameter[filament_extruder_id]==0.35}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.03{elsif nozzle_diameter[filament_extruder_id]==0.6}0.02{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{else}0{endif} ; Legacy LA {else} M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.02{elsif nozzle_diameter[filament_extruder_id]==0.5}0.018{elsif nozzle_diameter[filament_extruder_id]==0.6}0.012{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{elsif nozzle_diameter[filament_extruder_id]==0.25}0.09{elsif nozzle_diameter[filament_extruder_id]==0.3}0.065{else}0{endif} ; Pressure advance {endif} M142 S40 ; set heatbreak target temp via *ABSPG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    ""
  ],
  "filament_notes": [
    "Material Description\nUltrafuse ASA is a high-performance thermoplastic with similar mechanical properties as ABS. ASA offers additional benefits such as high outdoor weather resistance. The UV resistance, toughness, and rigidity make it an ideal material to 3D-print outdoor fixtures and appliances without losing its properties or color. When also taking into account the high heat resistance and high chemical resistance, this filament is a good choice for many types of applications.\n\nPrinting Recommendations:\nApply Magigoo PC, 3D lac or Dimafix to a clean build plate to improve adhesion."
  ],
  "filament_colour": [
    "#FFF4CA"
  ],
  "filament_vendor": [
    "Forward AM"
  ],
  "filament_density": [
    "1.07"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.5"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.5"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/}\nM900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.04{elsif nozzle_diameter[filament_extruder_id]==0.25}0.1{elsif nozzle_diameter[filament_extruder_id]==0.3}0.06{elsif nozzle_diameter[filament_extruder_id]==0.35}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.03{elsif nozzle_diameter[filament_extruder_id]==0.6}0.02{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{else}0{endif} ; Legacy LA\n{else}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.02{elsif nozzle_diameter[filament_extruder_id]==0.5}0.018{elsif nozzle_diameter[filament_extruder_id]==0.6}0.012{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{elsif nozzle_diameter[filament_extruder_id]==0.25}0.09{elsif nozzle_diameter[filament_extruder_id]==0.3}0.065{else}0{endif} ; Pressure advance\n{endif}\n\nM142 S40 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "3"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
  ],
  "filament_cooling_final_speed": [
    "2.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "printer_model=~/.*XL.*/ and nozzle_diameter[0]==0.6 and printer_notes!~/.*HF_NOZZLE.*/"
  ],
  "filament_max_volumetric_speed": [
    "9"
  ],
  "filament_cooling_initial_speed": [
    "5"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "40"
  ],
  "fan_min_speed": [
    "15"
  ],
  "filament_type": [
    "ASA"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "265"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "nozzle_temperature_initial_layer": [
    "270"
  ],
  "filament_wipe": [
    "nil"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "filament_retract_lift": [
    "0"
  ],
  "idle_temperature": [
    "100"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_stamping_loading_speed": [
    "26.5"
  ],
  "filament_infill_max_crossing_speed": [
    "140"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "filament_travel_max_lift": [
    "1.5"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_multitool_ramming_flow": [
    "40"
  ],
  "filament_multitool_ramming_volume": [
    "5"
  ],
  "filament_retract_length_toolchange": [
    "20"
  ],
  "renamed_from": [
    "Ultrafuse ASA @PG 0.6"
  ],
  "name": "Ultrafuse ASA @XL 0.6",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:45