Ultrafuse ABS Fusion+ @XL HF0.6

Forward AM · ABS · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*ABSC*

→

Ultrafuse ABS

→

Ultrafuse ABS Fusion+

→

Ultrafuse ABS Fusion+ @XL

→

Ultrafuse ABS Fusion+ @XL HF0.6

Includes (3)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Settings

Basic information

Material variant: ABS inherited
Vendor: Forward AM inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.08 inherited

Print temperature

Nozzle (initial layer) (°C): 270 inherited
Nozzle (other layers) (°C): 265 overridden
was 270 (inherited)

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 20 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 34 via *ABS06HFXL*

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 inherited	100 inherited

Other settings

bridge fan speed: 25 inherited
compatible printers condition: printer_notes=~/.*XL.*/ and nozzle_diameter[0]==0.6 and printer_notes=~/.*HF_NOZZLE.*/ via *ABS06HFXL*
cooling: 1 inherited
cooling perimeter transition distance: 10 via *ABS06HFXL*
cooling slowdown logic: consistent_surface via *ABS06HFXL*
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 0 inherited
filament colour: #FFF8D9 inherited
filament cooling final speed: 2.5 via *ABSPG*
filament cooling initial speed: 5 via *ABSPG*
filament cooling moves: 3 via *ABSPG*
filament infill max crossing speed: 0 via *ABS06HFXL*
filament infill max speed: 0 via *ABS06HFXL*
filament load time: 10.5 via *ABSPG*
filament loading speed: 10 via *ABSPG*
filament loading speed start: 50 via *ABSPG*
filament minimal purge on wipe tower: 35 via *ABS06HFXL*
filament multitool ramming: 1 via *ABS06HFXL*
filament multitool ramming flow: 40 via *ABS06HFXL*
filament multitool ramming volume: 5 via *ABS06HFXL*
filament notes: Material Description ABS Fusion+ made with Polyscope XILOY™ 3D is an engineering filament which has been optimized for 3D-printing. This special grade has been developed in collaboration with Polyscope Polymers - renowned for its material solutions in the automotive industry. ABS is a thermoplastic which is used in many applications. Although ABS has been classified as a standard material in 3D-printing it is known to be quite challenging to process. ABS Fusion+ combines the properties of ABS with an improved processability. The filament is based on an ABS grade which can be directly printed on glass without any adhesives or tape and has a higher success rate of prints due to extreme low warping. inherited
filament ramming parameters: 250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387 via *ABSPG*
filament retract before travel: 2 inherited
filament retract layer change: 0 inherited
filament retract length toolchange: 20 via *ABS06HFXL*
filament retract lift: 0 inherited
filament soluble: 0 inherited
filament stamping distance: 45 via *ABSPG*
filament stamping loading speed: 26.5 via *ABSPG*
filament toolchange delay: 0 via *ABSPG*
filament travel max lift: 1.5 via *ABS06HFXL*
filament travel ramping lift: 1 via *ABS06HFXL*
filament travel slope: 1 via *ABS06HFXL*
filament unload time: 8.5 via *ABSPG*
filament unloading speed: 60 via *ABSPG*
filament unloading speed start: 60 via *ABSPG*
filament wipe: nil inherited
idle temperature: 100 via *ABSPG*
renamed from: Ultrafuse ABS Fusion+ @PG inherited
start filament gcode: M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.02{elsif nozzle_diameter[filament_extruder_id]==0.5}0.018{elsif nozzle_diameter[filament_extruder_id]==0.6}0.015{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{elsif nozzle_diameter[filament_extruder_id]==0.25}0.09{elsif nozzle_diameter[filament_extruder_id]==0.3}0.065{else}0{endif} ; Filament gcode M142 S40 ; set heatbreak target temp via *ABS06HFXL*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    ""
  ],
  "filament_notes": [
    "Material Description\nABS Fusion+ made with Polyscope XILOY\u2122 3D is an engineering filament which has been optimized for 3D-printing. This special grade has been developed in collaboration with Polyscope Polymers - renowned for its material solutions in the automotive industry. ABS is a thermoplastic which is used in many applications. Although ABS has been classified as a standard material in 3D-printing it is known to be quite challenging to process. ABS Fusion+ combines the properties of ABS with an improved processability. The filament is based on an ABS grade which can be directly printed on glass without any adhesives or tape and has a higher success rate of prints due to extreme low warping."
  ],
  "filament_colour": [
    "#FFF8D9"
  ],
  "filament_vendor": [
    "Forward AM"
  ],
  "filament_density": [
    "1.08"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.5"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.5"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.02{elsif nozzle_diameter[filament_extruder_id]==0.5}0.018{elsif nozzle_diameter[filament_extruder_id]==0.6}0.015{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{elsif nozzle_diameter[filament_extruder_id]==0.25}0.09{elsif nozzle_diameter[filament_extruder_id]==0.3}0.065{else}0{endif} ; Filament gcode\nM142 S40 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "3"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
  ],
  "filament_cooling_final_speed": [
    "2.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*XL.*/ and nozzle_diameter[0]==0.6 and printer_notes=~/.*HF_NOZZLE.*/"
  ],
  "filament_max_volumetric_speed": [
    "34"
  ],
  "filament_cooling_initial_speed": [
    "5"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "20"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_type": [
    "ABS"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "bridge_fan_speed": [
    "25"
  ],
  "nozzle_temperature": [
    "265"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "nozzle_temperature_initial_layer": [
    "270"
  ],
  "filament_wipe": [
    "nil"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "filament_retract_lift": [
    "0"
  ],
  "idle_temperature": [
    "100"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_stamping_loading_speed": [
    "26.5"
  ],
  "filament_infill_max_crossing_speed": [
    "0"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "filament_travel_max_lift": [
    "1.5"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_multitool_ramming_flow": [
    "40"
  ],
  "filament_multitool_ramming_volume": [
    "5"
  ],
  "filament_retract_length_toolchange": [
    "20"
  ],
  "renamed_from": [
    "Ultrafuse ABS Fusion+ @PG"
  ],
  "name": "Ultrafuse ABS Fusion+ @XL HF0.6",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:45