Prusament PP Glass Fiber @XL

Prusa · PP · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

Prusament PP Glass Fiber

→

Prusament PP Glass Fiber @XL

Includes (4)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Inherited from this (2)

Settings

Basic information

Material variant: PP inherited
Vendor: Prusa Polymers inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.05 inherited
Cost (/kg): 121.2 inherited

Print temperature

Nozzle (initial layer) (°C): 245 inherited
Nozzle (other layers) (°C): 245 inherited

Cooling

Fan minimum (%): 10 overridden
was 15 (inherited)
Fan maximum (%): 25 overridden
was 20 (inherited)
Disable fan for first N layers: 5 inherited
Full fan if layer below (sec): 25 inherited
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1.03 inherited
Max volumetric speed (mm³/s): 5 overridden
was 5 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 inherited	95 overridden was 95

Other settings

bridge fan speed: 70 overridden
was 100 (inherited)
compatible printers condition: nozzle_diameter[0]>=0.4 and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8 and printer_notes=~/.*XL.*/ via *04PLUSXL*
cooling: 1 inherited
cooling perimeter transition distance: 10 via *PAXL*
cooling slowdown logic: consistent_surface via *PAXL*
end filament gcode: ; Filament-specific end gcode inherited
filament abrasive: 1 inherited
filament colour: #FFFFFF inherited
filament cooling final speed: 2.5 via *PCPG*
filament cooling initial speed: 5 via *PCPG*
filament cooling moves: 3 via *PCPG*
filament deretract speed: 20 inherited
filament infill max crossing speed: 100 via *PCPG*
filament infill max speed: 0 via *PCPG*
filament load time: 10.5 via *PCPG*
filament loading speed: 10 via *PCPG*
filament loading speed start: 50 via *PCPG*
filament minimal purge on wipe tower: 35 via *PAXL*
filament multitool ramming: 0 overridden
filament multitool ramming flow: 5 overridden
filament multitool ramming volume: 40 overridden
filament ramming parameters: 250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387 via *PCPG*
filament retract before travel: 2 inherited
filament retract before wipe: nil overridden
was 80% (inherited)
filament retract layer change: 0 inherited
filament retract length: 2 inherited
filament retract length toolchange: 2 overridden
filament retract speed: 60 inherited
filament soluble: 0 inherited
filament spool weight: 278 inherited
filament stamping distance: 45 via *PCPG*
filament stamping loading speed: 26.5 via *PCPG*
filament toolchange delay: 0 via *PCPG*
filament travel max lift: 0.6 overridden
filament travel ramping lift: 1 via *PAXL*
filament travel slope: 1 via *PAXL*
filament unload time: 8.5 via *PCPG*
filament unloading speed: 60 via *PCPG*
filament unloading speed start: 60 via *PCPG*
filament wipe: 1 inherited
idle temperature: 70 overridden
start filament gcode: M900 K0 ; Filament gcode M142 S36 ; set heatbreak target temp via *PA_PP_Glass*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "121.2"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#FFFFFF"
  ],
  "filament_vendor": [
    "Prusa Polymers"
  ],
  "filament_density": [
    "1.05"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.5"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1.03"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.5"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "M900 K0 ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "3"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
  ],
  "filament_cooling_final_speed": [
    "2.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "nozzle_diameter[0]>=0.4 and nozzle_diameter[0]!=0.6 and nozzle_diameter[0]!=0.8 and printer_notes=~/.*XL.*/"
  ],
  "filament_max_volumetric_speed": [
    "5"
  ],
  "filament_cooling_initial_speed": [
    "5"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_max_speed": [
    "25"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_type": [
    "PP"
  ],
  "filament_wipe": [
    "1"
  ],
  "hot_plate_temp": [
    "95"
  ],
  "bridge_fan_speed": [
    "70"
  ],
  "filament_abrasive": [
    "1"
  ],
  "nozzle_temperature": [
    "245"
  ],
  "filament_spool_weight": [
    "278"
  ],
  "fan_cooling_layer_time": [
    "25"
  ],
  "filament_retract_speed": [
    "60"
  ],
  "filament_retract_length": [
    "2"
  ],
  "filament_deretract_speed": [
    "20"
  ],
  "close_fan_the_first_x_layers": [
    "5"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_layer_change": [
    "0"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "idle_temperature": [
    "70"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_stamping_loading_speed": [
    "26.5"
  ],
  "filament_infill_max_crossing_speed": [
    "100"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "filament_travel_max_lift": [
    "0.6"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_multitool_ramming_flow": [
    "5"
  ],
  "filament_multitool_ramming_volume": [
    "40"
  ],
  "filament_retract_length_toolchange": [
    "2"
  ],
  "name": "Prusament PP Glass Fiber @XL",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:32