Prusament PC Blend @XL 0.8

Prusa · PC · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*ABS*

→

Prusament PC Blend

→

Prusament PC Blend @XL

→

Prusament PC Blend @XL 0.8

Includes (4)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Inherited from this (1)

Prusament PC Blend @XL HF0.8

Settings

Basic information

Material variant: PC inherited
Vendor: Prusa Polymers inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.22 inherited
Cost (/kg): 51.53 inherited

Print temperature

Nozzle (initial layer) (°C): 275 inherited
Nozzle (other layers) (°C): 275 inherited
Chamber (°C): 55 inherited

Cooling

Fan minimum (%): 20 inherited
Fan maximum (%): 20 inherited
Disable fan for first N layers: 4 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 10 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 0.93 inherited
Max volumetric speed (mm³/s): 18 overridden
was 12 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 via include	105 via include

Other settings

bridge fan speed: 30 inherited
chamber minimal temperature: 40 inherited
compatible printers condition: printer_model=~/.*XL.*/ and nozzle_diameter[0]==0.8 and printer_notes!~/.*HF_NOZZLE.*/ via *PC08XL*
cooling: 1 inherited
cooling perimeter transition distance: 10 via *PC08XL*
cooling slowdown logic: consistent_surface via *PC08XL*
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 0 inherited
filament colour: #DEE0E6 inherited
filament cooling final speed: 2.5 via *PCPG*
filament cooling initial speed: 5 via *PCPG*
filament cooling moves: 3 via *PCPG*
filament infill max crossing speed: 100 via *PCPG*
filament infill max speed: 0 via *PCPG*
filament load time: 10.5 via *PCPG*
filament loading speed: 10 via *PCPG*
filament loading speed start: 50 via *PCPG*
filament minimal purge on wipe tower: 35 via *PC08XL*
filament multitool ramming: 1 via *PC08XL*
filament multitool ramming flow: 40 via *PC08XL*
filament multitool ramming volume: 10 via *PC08XL*
filament ramming parameters: 250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387 via *PCPG*
filament retract length toolchange: 20 via *PC08XL*
filament retract lift: 0.2 inherited
filament soluble: 0 inherited
filament spool weight: 278 inherited
filament stamping distance: 45 via *PCPG*
filament stamping loading speed: 26.5 via *PCPG*
filament toolchange delay: 0 via *PCPG*
filament travel max lift: 1.5 via *PC08XL*
filament travel ramping lift: 1 via *PC08XL*
filament travel slope: 1 via *PC08XL*
filament unload time: 8.5 via *PCPG*
filament unloading speed: 60 via *PCPG*
filament unloading speed start: 60 via *PCPG*
full fan speed layer: 0 inherited
idle temperature: 150 via *PC08XL*
renamed from: Prusament PC Blend @PG 0.8 overridden
was Prusament PC Blend @PG (inherited)
start filament gcode: {if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/} M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Legacy LA {else} M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.6}0.025{elsif nozzle_diameter[filament_extruder_id]==0.8}0.016{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Pressure advance {endif} M142 S45 ; set heatbreak target temp via *PCPG*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "51.53"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#DEE0E6"
  ],
  "filament_vendor": [
    "Prusa Polymers"
  ],
  "filament_density": [
    "1.22"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.5"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "0.93"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.5"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/}\nM900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Legacy LA\n{else}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.6}0.025{elsif nozzle_diameter[filament_extruder_id]==0.8}0.016{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Pressure advance\n{endif}\n\nM142 S45 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "3"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
  ],
  "filament_cooling_final_speed": [
    "2.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "printer_model=~/.*XL.*/ and nozzle_diameter[0]==0.8 and printer_notes!~/.*HF_NOZZLE.*/"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "filament_cooling_initial_speed": [
    "5"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "20"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_type": [
    "PC"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "bridge_fan_speed": [
    "30"
  ],
  "nozzle_temperature": [
    "275"
  ],
  "chamber_temperature": [
    "55"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "chamber_minimal_temperature": [
    "40"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "nozzle_temperature_initial_layer": [
    "275"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_retract_lift": [
    "0.2"
  ],
  "filament_spool_weight": [
    "278"
  ],
  "idle_temperature": [
    "150"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_stamping_loading_speed": [
    "26.5"
  ],
  "filament_infill_max_crossing_speed": [
    "100"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "filament_travel_max_lift": [
    "1.5"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_multitool_ramming_flow": [
    "40"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_retract_length_toolchange": [
    "20"
  ],
  "renamed_from": [
    "Prusament PC Blend @PG 0.8"
  ],
  "name": "Prusament PC Blend @XL 0.8",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:31