Buddy3D ASA @XL HF0.8

Buddy3D · OTHER · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

Prusament ASA @XL 0.8

→

Prusament ASA @XL HF0.8

→

Buddy3D ASA @XL HF0.8

Includes (5)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Settings

Basic information

Material variant: ASA inherited
Vendor: Buddy3D overridden
was Prusa Polymers (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.07 inherited
Cost (/kg): 23.99 overridden
was 35.28 (inherited)

Print temperature

Nozzle (initial layer) (°C): 270 inherited
Nozzle (other layers) (°C): 270 inherited
Chamber (°C): 55 inherited

Cooling

Fan minimum (%): 20 inherited
Fan maximum (%): 20 inherited
Disable fan for first N layers: 4 inherited
Full fan if layer below (sec): 20 inherited
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 0.93 inherited
Max volumetric speed (mm³/s): 27 overridden
was 36 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 inherited	105 inherited

Other settings

bridge fan speed: 30 inherited
chamber minimal temperature: 40 inherited
compatible printers condition: printer_notes=~/.*XL.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*HF_NOZZLE.*/ via *ABS08HFXL*
cooling: 1 inherited
cooling perimeter transition distance: 10 via *ABS08HFXL*
cooling slowdown logic: consistent_surface via *ABS08HFXL*
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #FFF2EC inherited
filament cooling final speed: 2.5 via *ABSPG*
filament cooling initial speed: 5 via *ABSPG*
filament cooling moves: 3 via *ABSPG*
filament infill max crossing speed: 0 via *ABS08HFXL*
filament infill max speed: 0 via *ABS08HFXL*
filament load time: 10.5 via *ABSPG*
filament loading speed: 10 via *ABSPG*
filament loading speed start: 50 via *ABSPG*
filament minimal purge on wipe tower: 35 via *ABS08HFXL*
filament multitool ramming: 1 via *ABS08HFXL*
filament multitool ramming flow: 40 via *ABS08HFXL*
filament multitool ramming volume: 5 via *ABS08HFXL*
filament ramming parameters: 250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387 via *ABSPG*
filament retract length toolchange: 20 via *ABS08HFXL*
filament soluble: 0 inherited
filament spool weight: 278 inherited
filament stamping distance: 45 via *ABSPG*
filament stamping loading speed: 26.5 via *ABSPG*
filament toolchange delay: 0 via *ABSPG*
filament travel max lift: 1.5 via *ABS08HFXL*
filament travel ramping lift: 1 via *ABS08HFXL*
filament travel slope: 1 via *ABS08HFXL*
filament unload time: 8.5 via *ABSPG*
filament unloading speed: 60 via *ABSPG*
filament unloading speed start: 60 via *ABSPG*
full fan speed layer: 0 inherited
idle temperature: 100 via *ABSPG*
renamed from: Prusament ASA @PG 0.8 inherited
start filament gcode: M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.03{elsif nozzle_diameter[filament_extruder_id]==0.5}0.025{elsif nozzle_diameter[filament_extruder_id]==0.6}0.02{elsif nozzle_diameter[filament_extruder_id]==0.8}0.014{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.08{else}0{endif} ; Filament gcode M142 S40 ; set heatbreak target temp via *PA_Buddy3D_ASA*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "23.99"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#FFF2EC"
  ],
  "filament_vendor": [
    "Buddy3D"
  ],
  "filament_density": [
    "1.07"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "10.5"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "0.93"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "8.5"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    "M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.03{elsif nozzle_diameter[filament_extruder_id]==0.5}0.025{elsif nozzle_diameter[filament_extruder_id]==0.6}0.02{elsif nozzle_diameter[filament_extruder_id]==0.8}0.014{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.08{else}0{endif} ; Filament gcode\nM142 S40 ; set heatbreak target temp"
  ],
  "filament_cooling_moves": [
    "3"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_unloading_speed": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
  ],
  "filament_cooling_final_speed": [
    "2.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*XL.*/ and nozzle_diameter[0]==0.8 and printer_notes=~/.*HF_NOZZLE.*/"
  ],
  "filament_max_volumetric_speed": [
    "27"
  ],
  "filament_cooling_initial_speed": [
    "5"
  ],
  "filament_unloading_speed_start": [
    "60"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "20"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_type": [
    "ASA"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "bridge_fan_speed": [
    "30"
  ],
  "nozzle_temperature": [
    "270"
  ],
  "chamber_temperature": [
    "55"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "chamber_minimal_temperature": [
    "40"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "nozzle_temperature_initial_layer": [
    "270"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_spool_weight": [
    "278"
  ],
  "idle_temperature": [
    "100"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_stamping_loading_speed": [
    "26.5"
  ],
  "filament_infill_max_crossing_speed": [
    "0"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "filament_travel_max_lift": [
    "1.5"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "filament_multitool_ramming_flow": [
    "40"
  ],
  "filament_multitool_ramming_volume": [
    "5"
  ],
  "filament_retract_length_toolchange": [
    "20"
  ],
  "renamed_from": [
    "Prusament ASA @PG 0.8"
  ],
  "name": "Buddy3D ASA @XL HF0.8",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:28