*ABS08HF*
Unknown · OTHER
· by prusa-system
· 0 downloads
Inheritance
-
*ABSPG*
→
*ABS08PG*
→
*ABS08HF*
Includes (1)
Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.
Settings
Cooling
- Slow down if layer below (sec)
-
25 inherited
Flow
- Max volumetric speed (mm³/s)
-
36 overriddenwas 18 (inherited)
Other settings
- compatible printers condition
-
printer_model=~/(MK4|MK4IS|MK4ISMMU3|MK3.9|MK3.9MMU3)/ and nozzle_diameter[0]==0.8 and nozzle_high_flow[0] and ! single_extruder_multi_material overriddenwas printer_model=~/(MK4|MK4IS|MK4ISMMU3|MK3.9|MK3.9MMU3)/ and nozzle_diameter[0]==0.8 and ! nozzle_high_flow[0] and ! single_extruder_multi_material (inherited)
- cooling perimeter transition distance
-
10 inherited
- cooling slowdown logic
-
consistent_surface inherited
- filament cooling final speed
-
2.5 inherited
- filament cooling initial speed
-
5 inherited
- filament cooling moves
-
3 inherited
- filament infill max crossing speed
-
0 overriddenwas 0 (inherited)
- filament infill max speed
-
0 overriddenwas 0 (inherited)
- filament load time
-
10.5 inherited
- filament loading speed
-
10 inherited
- filament loading speed start
-
50 inherited
- filament minimal purge on wipe tower
-
35 inherited
- filament ramming parameters
-
250 100 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387 overriddenwas 250 100 42.4194 42.4194 42.4194 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387 (inherited)
- filament stamping distance
-
45 inherited
- filament stamping loading speed
-
26.5 inherited
- filament toolchange delay
-
0 inherited
- filament unload time
-
8.5 inherited
- filament unloading speed
-
60 inherited
- filament unloading speed start
-
60 inherited
- idle temperature
-
100 inherited
- start filament gcode
-
M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.02{elsif nozzle_diameter[filament_extruder_id]==0.5}0.018{elsif nozzle_diameter[filament_extruder_id]==0.6}0.015{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{elsif nozzle_diameter[filament_extruder_id]==0.25}0.09{elsif nozzle_diameter[filament_extruder_id]==0.3}0.065{else}0{endif} ; Filament gcode M142 S40 ; set heatbreak target temp via *PA_ABSHF*
Raw resolved JSON
{
"idle_temperature": [
"100"
],
"filament_load_time": [
"10.5"
],
"filament_unload_time": [
"8.5"
],
"start_filament_gcode": [
"M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.02{elsif nozzle_diameter[filament_extruder_id]==0.5}0.018{elsif nozzle_diameter[filament_extruder_id]==0.6}0.015{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{elsif nozzle_diameter[filament_extruder_id]==0.25}0.09{elsif nozzle_diameter[filament_extruder_id]==0.3}0.065{else}0{endif} ; Filament gcode\nM142 S40 ; set heatbreak target temp"
],
"cooling_slowdown_logic": [
"consistent_surface"
],
"filament_cooling_moves": [
"3"
],
"filament_loading_speed": [
"10"
],
"filament_unloading_speed": [
"60"
],
"filament_infill_max_speed": [
"0"
],
"filament_toolchange_delay": [
"0"
],
"filament_stamping_distance": [
"45"
],
"filament_ramming_parameters": [
"250 100 42.4194 42.4194| 0.05 42.4387 0.45 42.4387 0.95 42.4387 1.45 42.4387 1.95 42.4387 2.45 42.4387 2.95 42.4387 3.45 42.4387 3.95 42.4387 4.45 42.4387 4.95 42.4387"
],
"filament_cooling_final_speed": [
"2.5"
],
"filament_loading_speed_start": [
"50"
],
"compatible_printers_condition": [
"printer_model=~/(MK4|MK4IS|MK4ISMMU3|MK3.9|MK3.9MMU3)/ and nozzle_diameter[0]==0.8 and nozzle_high_flow[0] and ! single_extruder_multi_material"
],
"filament_max_volumetric_speed": [
"36"
],
"filament_cooling_initial_speed": [
"5"
],
"filament_unloading_speed_start": [
"60"
],
"filament_stamping_loading_speed": [
"26.5"
],
"filament_infill_max_crossing_speed": [
"0"
],
"filament_minimal_purge_on_wipe_tower": [
"35"
],
"cooling_perimeter_transition_distance": [
"10"
],
"slow_down_layer_time": [
"25"
],
"name": "*ABS08HF*",
"filament_settings_id": [
"*ABS08HF*"
],
"type": "filament"
}
Version history
View full history with diffs →- v1 created 2026-05-19 11:27