Layer Line DuraPET @HSP1 0.8 Takoto

Unknown · PETG · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*PET*

→

*Layer Line DuraPET*

→

Layer Line DuraPET @HSP1 0.8 Takoto

Includes (2)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Settings

Basic information

Material variant: PETG inherited
Vendor: HartSmart Products via *Layer Line*
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.29 inherited
Cost (/kg): 29.99 inherited

Print temperature

Nozzle (initial layer) (°C): 280 overridden
was 240 (inherited)
Nozzle (other layers) (°C): 285 overridden
was 235 (inherited)

Cooling

Fan minimum (%): 80 overridden
was 20 (inherited)
Fan maximum (%): 80 overridden
was 40 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 15 inherited
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1.00 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 20 overridden
was 0 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	80 overridden was 85	80 overridden was 85

Other settings

bridge fan speed: 80 overridden
was 40 (inherited)
compatible printers condition: nozzle_diameter[0]==0.8 via *0.8 Takoto*
cooling: 1 inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #C0C0C0 inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament notes: Layer Line DuraPET inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament soluble: 0 inherited
filament spool weight: 200 via *Layer Line*
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
start filament gcode: ; Filament gcode {local pressure_advance = 0.0} {if printer_notes=~/.*DUPLICATOR_MODE.*/} M572 D0:1 S{pressure_advance} {else} M572 D{current_extruder} S{pressure_advance} {endif} overridden
was ; Filament-specific start gcode (inherited)

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "29.99"
  ],
  "filament_notes": [
    "Layer Line DuraPET"
  ],
  "filament_colour": [
    "#C0C0C0"
  ],
  "filament_vendor": [
    "HartSmart Products"
  ],
  "filament_density": [
    "1.29"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1.00"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "; Filament gcode\n{local pressure_advance = 0.0}\n{if printer_notes=~/.*DUPLICATOR_MODE.*/}\nM572 D0:1 S{pressure_advance}\n{else}\nM572 D{current_extruder} S{pressure_advance}\n{endif}"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "nozzle_diameter[0]==0.8"
  ],
  "filament_max_volumetric_speed": [
    "20"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "80"
  ],
  "filament_type": [
    "PETG"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "bridge_fan_speed": [
    "80"
  ],
  "nozzle_temperature": [
    "285"
  ],
  "fan_cooling_layer_time": [
    "15"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "nozzle_temperature_initial_layer": [
    "280"
  ],
  "filament_spool_weight": [
    "200"
  ],
  "name": "Layer Line DuraPET @HSP1 0.8 Takoto",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:26