Bambu ASA @BBL X2D 0.4 nozzle

Bambu Lab · ASA · 0.40mm nozzle · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

Bambu ASA @base

→

Bambu ASA @BBL X2D 0.4 nozzle

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

fdm_filament_template_direct_bowden

Compatible printers (1)

Bambu Lab X2D 0.4 nozzle

Settings

Basic information

Material variant: ASA inherited
Vendor: Bambu Lab inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.05 inherited
Cost (/kg): 31.99 inherited

Print temperature

Nozzle (initial layer) (°C): 270 overridden
was 270 (inherited)
Nozzle (other layers) (°C): 270 overridden
was 270 (inherited)

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 35 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 35 inherited
Slow down if layer below (sec): 12 inherited
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 0.95 overridden
was 0.95 (inherited)
Max volumetric speed (mm³/s): 18 overridden
was 18 (inherited)

Retraction

Retraction length (mm): 0.4 overridden
was nil (inherited)
Retraction speed (mm/s): nil via fdm_filament_template_direct_bowden
Deretraction speed (mm/s): nil via fdm_filament_template_direct_bowden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	95 inherited	95 inherited
Engineering Plate	100 inherited	100 inherited
High Temp Plate	100 inherited	100 inherited
Textured PEI Plate	100 inherited	100 inherited

Other settings

additional fan full speed layer: 0 inherited
chamber temperatures: 65 overridden
close additional fan first x layers: 3 inherited
compatible printers: Bambu Lab X2D 0.4 nozzle overridden
counter coef 2: 0.0094 overridden
counter coef 3: -0.0092 overridden
counter limit max: 0.2258 overridden
counter limit min: -0.0092 overridden
description: When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials. inherited
filament adaptive volumetric speed: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament bridge speed: 25, 25, 25, 25 via fdm_filament_template_direct_bowden
filament cooling before tower: 10, 10, 10, 10 overridden
filament enable overhang speed: 1, 1, 1, 1 via fdm_filament_template_direct_bowden
filament extruder compatibility: 24 overridden
filament extruder variant: Direct Drive Standard, Direct Drive High Flow, Bowden Standard, Bowden High Flow via fdm_filament_template_direct_bowden
filament flush temp: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament flush volumetric speed: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament id: GFB01 inherited
filament is support: 0 inherited
filament long retractions when cut: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament minimal purge on wipe tower: 15 inherited
filament overhang 1 4 speed: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament overhang 2 4 speed: 50, 50, 50, 50 via fdm_filament_template_direct_bowden
filament overhang 3 4 speed: 30, 30, 30, 30 via fdm_filament_template_direct_bowden
filament overhang 4 4 speed: 10, 10, 10, 10 via fdm_filament_template_direct_bowden
filament overhang totally speed: 10, 10, 10, 10 via fdm_filament_template_direct_bowden
filament pre cooling temperature: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament pre cooling temperature nc: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament ramming travel time: 0, 0, 0, 0 overridden
filament ramming travel time nc: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament ramming volumetric speed: -1, -1, -1, -1 via fdm_filament_template_direct_bowden
filament ramming volumetric speed nc: -1, -1, -1, -1 via fdm_filament_template_direct_bowden
filament retract before wipe: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament retract length nc: 14, 14, 14, 14 via fdm_filament_template_direct_bowden
filament retract restart extra: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament retract when changing layer: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament retraction distances when cut: 10, 10, 10, 10 overridden
filament retraction minimum travel: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament soluble: 0 inherited
filament tower interface print temp: 270 overridden
filament wipe: 1, 1, 1, 1 overridden
was nil (inherited)
filament wipe distance: 1, 1, 1, 1 overridden
was nil (inherited)
filament z hop: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament z hop types: Spiral Lift, Spiral Lift, Spiral Lift, Spiral Lift overridden
full fan speed layer: 0 inherited
hole coef 2: 0.0013 overridden
hole coef 3: 0.1261 overridden
hole limit max: 0.1586 overridden
hole limit min: 0.1261 overridden
impact strength z: 4.9 inherited
instantiation: true overridden
was false (inherited)
long retractions when ec: 1, 1, 1, 1 via fdm_filament_template_direct_bowden
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 80 inherited
overhang fan threshold: 25% inherited
override process overhang speed: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
retraction distances when ec: 3, 3, 4, 4 overridden
setting id: GFSB01_22 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited
volumetric speed coefficients: 0 0 0 0 0 0, 0 0 0 0 0 0, 0 0 0 0 0 0, 0 0 0 0 0 0 via fdm_filament_template_direct_bowden

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "35"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "31.99"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "1",
    "1",
    "1",
    "1"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "95"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "1.05"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "270",
    "270",
    "270",
    "270"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "0.95",
    "0.95",
    "0.95",
    "0.95"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20",
    "20",
    "20",
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "35"
  ],
  "filament_wipe_distance": [
    "1",
    "1",
    "1",
    "1"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "0.4",
    "0.4",
    "nil",
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "95"
  ],
  "filament_max_volumetric_speed": [
    "18",
    "25",
    "18",
    "20"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "270",
    "270",
    "270",
    "270"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "description": "When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.",
  "filament_id": "GFB01",
  "impact_strength_z": [
    "4.9"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_flush_temp": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_z_hop_types": [
    "Spiral Lift",
    "Spiral Lift",
    "Spiral Lift",
    "Spiral Lift"
  ],
  "filament_bridge_speed": [
    "25",
    "25",
    "25",
    "25"
  ],
  "long_retractions_when_ec": [
    "1",
    "1",
    "1",
    "1"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow",
    "Bowden Standard",
    "Bowden High Flow"
  ],
  "filament_retract_length_nc": [
    "14",
    "14",
    "14",
    "14"
  ],
  "filament_overhang_1_4_speed": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_overhang_2_4_speed": [
    "50",
    "50",
    "50",
    "50"
  ],
  "filament_overhang_3_4_speed": [
    "30",
    "30",
    "30",
    "30"
  ],
  "filament_overhang_4_4_speed": [
    "10",
    "10",
    "10",
    "10"
  ],
  "retraction_distances_when_ec": [
    "3",
    "3",
    "4",
    "4"
  ],
  "filament_cooling_before_tower": [
    "10",
    "10",
    "10",
    "10"
  ],
  "volumetric_speed_coefficients": [
    "0 0 0 0 0 0",
    "0 0 0 0 0 0",
    "0 0 0 0 0 0",
    "0 0 0 0 0 0"
  ],
  "filament_enable_overhang_speed": [
    "1",
    "1",
    "1",
    "1"
  ],
  "filament_flush_volumetric_speed": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_overhang_totally_speed": [
    "10",
    "10",
    "10",
    "10"
  ],
  "filament_ramming_travel_time_nc": [
    "0",
    "0",
    "0",
    "0"
  ],
  "override_process_overhang_speed": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed": [
    "-1",
    "-1",
    "-1",
    "-1"
  ],
  "filament_adaptive_volumetric_speed": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "filament_pre_cooling_temperature_nc": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed_nc": [
    "-1",
    "-1",
    "-1",
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "10",
    "10",
    "10",
    "10"
  ],
  "setting_id": "GFSB01_22",
  "hole_coef_2": [
    "0.0013"
  ],
  "hole_coef_3": [
    "0.1261"
  ],
  "counter_coef_2": [
    "0.0094"
  ],
  "counter_coef_3": [
    "-0.0092"
  ],
  "hole_limit_max": [
    "0.1586"
  ],
  "hole_limit_min": [
    "0.1261"
  ],
  "counter_limit_max": [
    "0.2258"
  ],
  "counter_limit_min": [
    "-0.0092"
  ],
  "compatible_printers": [
    "Bambu Lab X2D 0.4 nozzle"
  ],
  "chamber_temperatures": [
    "65"
  ],
  "filament_ramming_travel_time": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_extruder_compatibility": [
    "24"
  ],
  "filament_tower_interface_print_temp": [
    "270"
  ],
  "name": "Bambu ASA @BBL X2D 0.4 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:16