Prusament PETG Carbon Fiber @AQD

Prusa · PETGCF · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

Prusament PETG Carbon Fiber @AQI

→

Prusament PETG Carbon Fiber @AQD

Includes (3)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

Settings

Basic information

Material variant: PETGCF inherited
Vendor: Generic via *AQD 0.4*
Diameter (mm): 1.75 via *AQD 0.4*
Density (g/cm³): 1.27 inherited
Cost (/kg): 0 via *AQD 0.4*

Print temperature

Nozzle (initial layer) (°C): 275 inherited
Nozzle (other layers) (°C): 275 inherited

Cooling

Fan minimum (%): 55 inherited
Fan maximum (%): 80 inherited
Disable fan for first N layers: 3 via *AQD 0.4*
Full fan if layer below (sec): 20 inherited
Slow down if layer below (sec): 2 inherited
Min speed when slowed (mm/s): 18 inherited

Flow

Flow ratio: 1 via *AQD 0.4*
Max volumetric speed (mm³/s): 15 via *AQD 0.4*

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	85 inherited	85 inherited

Other settings

bridge fan speed: 90% inherited
compatible printers condition: printer_notes=~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes=~/.*PRINTER_MODEL_AQD.*/ and nozzle_diameter[0]==0.4 via *AQD 0.4*
cooling: 1 inherited
fan always on: 1 inherited
filament colour: #EC626F via *AQD 0.4*
filament deretract speed: 25 inherited
filament minimal purge on wipe tower: 15 via *AQD 0.4*
filament notes: CU via *AQD 0.4*
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 via *AQD 0.4*
filament retract before travel: 2.5 inherited
filament retract before wipe: 50% inherited
filament retract layer change: 1 inherited
filament retract length: 3.5 inherited
filament retract lift: 0.2 inherited
filament retract speed: 30 inherited
filament soluble: 0 via *AQD 0.4*
filament spool weight: 250 via *AQD 0.4*
filament toolchange delay: 0 via *AQD 0.4*
filament wipe: 1 inherited
renamed from: DeltiQ - PETG - Generic inherited

Raw resolved JSON

{
  "filament_cost": [
    "0"
  ],
  "filament_notes": [
    "CU"
  ],
  "filament_colour": [
    "#EC626F"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_spool_weight": [
    "250"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes=~/.*PRINTER_MODEL_AQD.*/ and nozzle_diameter[0]==0.4"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "cooling": [
    "1"
  ],
  "renamed_from": [
    "DeltiQ - PETG - Generic"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "55"
  ],
  "filament_type": [
    "PETGCF"
  ],
  "filament_wipe": [
    "1"
  ],
  "hot_plate_temp": [
    "85"
  ],
  "bridge_fan_speed": [
    "90%"
  ],
  "filament_density": [
    "1.27"
  ],
  "nozzle_temperature": [
    "275"
  ],
  "slow_down_min_speed": [
    "18"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "filament_retract_lift": [
    "0.2"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_retract_speed": [
    "30"
  ],
  "filament_retract_length": [
    "3.5"
  ],
  "filament_deretract_speed": [
    "25"
  ],
  "filament_retract_before_wipe": [
    "50%"
  ],
  "hot_plate_temp_initial_layer": [
    "85"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_retract_layer_change": [
    "1"
  ],
  "filament_retract_before_travel": [
    "2.5"
  ],
  "nozzle_temperature_initial_layer": [
    "275"
  ],
  "name": "Prusament PETG Carbon Fiber @AQD",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:26