Prusament PLA (Door Opened) @AQI

Prusa · PLA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*DQ2 0.4*

→

Generic PLA @DQ2

→

Prusament PLA @DQ2

→

Prusament PLA (Door Opened) @AQI

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

*AQI 0.4*

Inherited from this (1)

Prusament PLA (Door Opened) @AQD

Settings

Basic information

Material variant: PLA inherited
Vendor: Generic via *AQI 0.4*
Diameter (mm): 1.75 via *AQI 0.4*
Density (g/cm³): 1.24 inherited
Cost (/kg): 0 via *AQI 0.4*

Print temperature

Nozzle (initial layer) (°C): 230 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 230 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 100 overridden
was 100 (inherited)
Fan maximum (%): 100 inherited
Disable fan for first N layers: 3 via *AQI 0.4*
Full fan if layer below (sec): 20 overridden
was 100 (inherited)
Slow down if layer below (sec): 1 overridden
was 4 (inherited)
Min speed when slowed (mm/s): 18 overridden
was 10 (inherited)

Flow

Flow ratio: 1 via *AQI 0.4*
Max volumetric speed (mm³/s): 15 via *AQI 0.4*

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	55 overridden was 50	55 overridden was 50

Other settings

bridge fan speed: 100 inherited
compatible printers condition: printer_notes=~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes=~/.*PRINTER_MODEL_AQI.*/ and nozzle_diameter[0]==0.4 via *AQI 0.4*
cooling: 1 inherited
fan always on: 1 inherited
filament colour: #EC626F via *AQI 0.4*
filament deretract speed: nil inherited
filament minimal purge on wipe tower: 15 via *AQI 0.4*
filament notes: CU via *AQI 0.4*
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 via *AQI 0.4*
filament retract before travel: 2 inherited
filament retract before wipe: 90% overridden
was 90% (inherited)
filament retract layer change: 1 inherited
filament retract length: 3.7 overridden
was 4.2 (inherited)
filament retract lift: 0.2 inherited
filament retract lift above: nil inherited
filament retract lift below: nil inherited
filament retract restart extra: nil inherited
filament retract speed: 29 overridden
was 30 (inherited)
filament soluble: 0 via *AQI 0.4*
filament spool weight: 250 via *AQI 0.4*
filament toolchange delay: 0 via *AQI 0.4*
filament wipe: 1 inherited
full fan speed layer: 0 inherited
renamed from: DeltiQ - PLA - Prusament (Prusa Polymers) inherited
start filament gcode: ; FILAMENT_START_GCODE M191 S0 ; Wait for chamber temperature overridden

Raw resolved JSON

{
  "filament_cost": [
    "0"
  ],
  "filament_notes": [
    "CU"
  ],
  "filament_colour": [
    "#EC626F"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_spool_weight": [
    "250"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes=~/.*PRINTER_MODEL_AQI.*/ and nozzle_diameter[0]==0.4"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "cooling": [
    "1"
  ],
  "renamed_from": [
    "DeltiQ - PLA - Prusament (Prusa Polymers)"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "1"
  ],
  "hot_plate_temp": [
    "55"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "filament_density": [
    "1.24"
  ],
  "nozzle_temperature": [
    "230"
  ],
  "slow_down_min_speed": [
    "18"
  ],
  "slow_down_layer_time": [
    "1"
  ],
  "filament_retract_lift": [
    "0.2"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_retract_speed": [
    "29"
  ],
  "filament_retract_length": [
    "3.7"
  ],
  "filament_retract_before_wipe": [
    "90%"
  ],
  "hot_plate_temp_initial_layer": [
    "55"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_retract_layer_change": [
    "1"
  ],
  "filament_retract_before_travel": [
    "2"
  ],
  "nozzle_temperature_initial_layer": [
    "230"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "start_filament_gcode": [
    "; FILAMENT_START_GCODE\nM191 S0 ; Wait for chamber temperature"
  ],
  "name": "Prusament PLA (Door Opened) @AQI",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:26