PLA @PROTON_XE750

Generic · PLA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*common PLA @INAT*

→

PLA @PROTON_XE750

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

*start_end_gcode @PROTON_XE750*

Settings

Basic information

Material variant: PLA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.25 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 210 inherited
Nozzle (other layers) (°C): 210 inherited

Cooling

Fan minimum (%): 50 inherited
Fan maximum (%): 100 inherited
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 0 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 inherited	60 inherited

Other settings

compatible printers: Proton XE-750 via *start_end_gcode @PROTON_XE750*
compatible printers condition: printer_notes=~/.*PRINTER_MODEL_VORON.*/ inherited
cooling: 1 inherited
end filament gcode: ; Filament end gcode BEGIN G0 X-5 Y250 F10000 M104 S{temperature[current_extruder] - 50} ; Filament end gcode END via *start_end_gcode @PROTON_XE750*
fan always on: 1 inherited
filament colour: #FF3232 inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
start filament gcode: ; Filament start gcode BEGIN M104 S[temperature[current_extruder]] G4 S20 ; Filament start gcode END via *start_end_gcode @PROTON_XE750*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#FF3232"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.25"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament end gcode BEGIN\nG0 X-5 Y250 F10000\nM104 S{temperature[current_extruder] - 50}\n; Filament end gcode END\n"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    "Proton XE-750"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "; Filament start gcode BEGIN\nM104 S[temperature[current_extruder]]\nG4 S20\n; Filament start gcode END\n"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_MODEL_VORON.*/"
  ],
  "filament_max_volumetric_speed": [
    "0"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "50"
  ],
  "filament_type": [
    "PLA"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "nozzle_temperature": [
    "210"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "nozzle_temperature_initial_layer": [
    "210"
  ],
  "name": "PLA @PROTON_XE750",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:26