Generic PLA @MMU 0.25

Generic · PLA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

→

Generic PLA @MMU 0.25

Inherited from this (1)

Prusa PLA @MMU 0.25

Settings

Basic information

Material variant: PLA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 27.82 inherited

Print temperature

Nozzle (initial layer) (°C): 215 inherited
Nozzle (other layers) (°C): 205 inherited
Chamber (°C): 20 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 12 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 3 overridden
was 10 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 inherited	55 inherited

Other settings

bridge fan speed: 100 inherited
chamber minimal temperature: 0 inherited
compatible printers condition: nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material overridden
was nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material (inherited)
cooling: 1 inherited
cooling perimeter transition distance: 10 inherited
cooling slowdown logic: consistent_surface inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #FF3232 inherited
filament cooling final speed: 2 inherited
filament cooling initial speed: 3 inherited
filament cooling moves: 1 inherited
filament load time: 15 inherited
filament loading speed: 14 inherited
filament loading speed start: 19 inherited
filament minimal purge on wipe tower: 10 overridden
was 15 (inherited)
filament ramming parameters: 200 120 2.70968 2.93548 3.29032 3.80645 4.58065 5.54839 6.54839 7.3871 7.93548 8.19355 8.16129 8.03226| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 7.98716 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6 overridden
was 130 120 2.70968 2.93548 3.32258 3.83871 4.58065 5.54839 6.51613 7.35484 7.93548 8.16129| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 11.342 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6 (inherited)
filament soluble: 0 inherited
filament spool weight: 230 inherited
filament toolchange delay: 0 inherited
filament unload time: 12 inherited
filament unloading speed: 20 inherited
filament unloading speed start: 100 inherited
full fan speed layer: 4 inherited
renamed from: Generic PLA @MMU2 0.25 overridden
was Generic PLA @MMU2 (inherited)
start filament gcode: ; Filament-specific start gcode inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "27.82"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#FF3232"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "15"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "12"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "start_filament_gcode": [
    "; Filament-specific start gcode"
  ],
  "filament_cooling_moves": [
    "1"
  ],
  "filament_loading_speed": [
    "14"
  ],
  "filament_unloading_speed": [
    "20"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "200 120 2.70968 2.93548 3.29032 3.80645 4.58065 5.54839 6.54839 7.3871 7.93548 8.19355 8.16129 8.03226| 0.05 2.66451 0.45 3.05805 0.95 4.05807 1.45 5.97742 1.95 7.69999 2.45 8.1936 2.95 7.98716 3.45 11.4065 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "2"
  ],
  "filament_loading_speed_start": [
    "19"
  ],
  "compatible_printers_condition": [
    "nozzle_diameter[0]==0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material"
  ],
  "filament_max_volumetric_speed": [
    "3"
  ],
  "filament_cooling_initial_speed": [
    "3"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "10"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_type": [
    "PLA"
  ],
  "hot_plate_temp": [
    "55"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "205"
  ],
  "chamber_temperature": [
    "20"
  ],
  "full_fan_speed_layer": [
    "4"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "chamber_minimal_temperature": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "nozzle_temperature_initial_layer": [
    "215"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_spool_weight": [
    "230"
  ],
  "renamed_from": [
    "Generic PLA @MMU2 0.25"
  ],
  "name": "Generic PLA @MMU 0.25",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:17