Generic PETG @lulzbot

Generic · PETG · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Settings

Basic information

Material variant: PETG overridden
Vendor: Generic overridden
Diameter (mm): 2.85 overridden
Density (g/cm³): 1.27 overridden
Cost (/kg): 27 overridden

Print temperature

Nozzle (initial layer) (°C): 235 overridden
Nozzle (other layers) (°C): 230 overridden

Cooling

Fan minimum (%): 40 overridden
Fan maximum (%): 80 overridden
Disable fan for first N layers: 3 overridden
Full fan if layer below (sec): 60 overridden
Slow down if layer below (sec): 10 overridden
Min speed when slowed (mm/s): 10 overridden

Flow

Flow ratio: 1 overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	65 overridden	60 overridden

Other settings

bridge fan speed: 100 overridden
cooling: 1 overridden
end filament gcode: ; Filament-specific end gcode ;END gcode for filament overridden
fan always on: 1 overridden
filament colour: #29B2B2 overridden
filament notes: Use glue stick. overridden
filament soluble: 0 overridden
filament toolchange delay: 0 overridden
start filament gcode: ; Filament gcode overridden

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "40"
  ],
  "filament_cost": [
    "27"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_notes": [
    "Use glue stick."
  ],
  "hot_plate_temp": [
    "60"
  ],
  "filament_colour": [
    "#29B2B2"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "2.85"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament\n"
  ],
  "nozzle_temperature": [
    "230"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "start_filament_gcode": [
    "; Filament gcode\n"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "65"
  ],
  "nozzle_temperature_initial_layer": [
    "235"
  ],
  "name": "Generic PETG @lulzbot",
  "filament_settings_id": [
    "Generic PETG @lulzbot"
  ],
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:15