Bambu ABS @BBL A1

Bambu Lab · ABS · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

Bambu ABS @base

→

Bambu ABS @BBL A1

Compatible printers (3)

Bambu Lab A1 0.4 nozzle
Bambu Lab A1 0.6 nozzle
Bambu Lab A1 0.8 nozzle

Settings

Basic information

Material variant: ABS inherited
Vendor: Bambu Lab inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 inherited
Cost (/kg): 24.99 inherited

Print temperature

Nozzle (initial layer) (°C): 240 inherited
Nozzle (other layers) (°C): 240 inherited

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 20 overridden
was 80 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 12 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 16 overridden
was 28.6 (inherited)

Retraction

Retraction length (mm): 0.4 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	95 inherited	95 inherited
Engineering Plate	95 inherited	95 inherited
High Temp Plate	100 overridden was 95	100 overridden was 95
Textured PEI Plate	100 overridden	100 overridden

Other settings

additional fan full speed layer: 0 inherited
close additional fan first x layers: 3 inherited
compatible printers: Bambu Lab A1 0.4 nozzle, Bambu Lab A1 0.6 nozzle, Bambu Lab A1 0.8 nozzle overridden
description: When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials. inherited
filament id: GFB00 inherited
filament is support: 0 inherited
filament long retractions when cut: 1 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when cut: 18 overridden
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
full fan speed layer: 0 inherited
impact strength z: 7.4 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 80 inherited
overhang fan threshold: 25% inherited
reduce fan stop start freq: 0 overridden
was 1 (inherited)
required nozzle HRC: 3 inherited
setting id: GFSB00_07 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "20"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "24.99"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "95"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "95"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "0.4"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "95"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "95"
  ],
  "filament_max_volumetric_speed": [
    "16"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "description": "When printing this filament, there's a risk of warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.",
  "filament_id": "GFB00",
  "impact_strength_z": [
    "7.4"
  ],
  "setting_id": "GFSB00_07",
  "compatible_printers": [
    "Bambu Lab A1 0.4 nozzle",
    "Bambu Lab A1 0.6 nozzle",
    "Bambu Lab A1 0.8 nozzle"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_long_retractions_when_cut": [
    "1"
  ],
  "filament_retraction_distances_when_cut": [
    "18"
  ],
  "name": "Bambu ABS @BBL A1"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:16