Prusament ASA @MMU

Prusa · ASA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

Prusament ASA @MMU

Inherited from this (3)

Settings

Basic information

Material variant: ASA overridden
was ABS (inherited)
Vendor: Prusa Polymers overridden
was Made for Prusa (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.07 overridden
was 1.08 (inherited)
Cost (/kg): 42.69 overridden
was 26.99 (inherited)

Print temperature

Nozzle (initial layer) (°C): 260 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 260 overridden
was 255 (inherited)

Cooling

Fan minimum (%): 20 overridden
was 15 (inherited)
Fan maximum (%): 20 overridden
was 15 (inherited)
Disable fan for first N layers: 4 overridden
was 4 (inherited)
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 15 overridden
was 20 (inherited)
Min speed when slowed (mm/s): 15 overridden
was 15 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 11 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	105 overridden was 100	110 overridden was 110

Other settings

bridge fan speed: 30 overridden
was 25 (inherited)
compatible printers condition: nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material inherited
cooling: 1 overridden
was 1 (inherited)
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 overridden
was 0 (inherited)
filament colour: #FFF2EC overridden
was #FFF2EC (inherited)
filament cooling final speed: 2 overridden
was 50 (inherited)
filament cooling initial speed: 3 overridden
was 10 (inherited)
filament cooling moves: 1 overridden
was 5 (inherited)
filament infill max crossing speed: 140 inherited
filament infill max speed: 0 inherited
filament load time: 15 inherited
filament loading speed: 14 inherited
filament loading speed start: 19 inherited
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6, inherited
filament soluble: 0 inherited
filament spool weight: 278 overridden
was 230 (inherited)
filament toolchange delay: 0 inherited
filament unload time: 12 inherited
filament unloading speed: 20 inherited
filament unloading speed start: 100 inherited
renamed from: Prusament ASA @MMU2 overridden
start filament gcode: {if printer_notes!~/.*(MK3.5|MINIIS).*/} M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0 {endif} {if printer_notes=~/.*MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif} {endif} {if printer_notes=~/.*MK3.5.*/} M572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode {endif} inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "42.69"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#FFF2EC"
  ],
  "filament_vendor": [
    "Prusa Polymers"
  ],
  "filament_density": [
    "1.07"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "15"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "12"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK3.5|MINIIS).*/}\nM900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.6}0.02{else}0.04{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K12{elsif nozzle_diameter[0]==0.8};{else}M900 K20{endif} ; Filament gcode LA 1.0\n{endif}\n\n{if printer_notes=~/.*MINIIS.*/}\nM572 S{if nozzle_diameter[0]==0.6}0.1{elsif nozzle_diameter[0]==0.8}0.07{elsif nozzle_diameter[0]==0.4}0.19{elsif nozzle_diameter[0]==0.25}0.55{else}0{endif}\n{endif}\n\n{if printer_notes=~/.*MK3.5.*/}\nM572 S{if nozzle_diameter[0]==0.4}0.02{elsif nozzle_diameter[0]==0.5}0.018{elsif nozzle_diameter[0]==0.6}0.012{elsif nozzle_diameter[0]==0.8}0.01{elsif nozzle_diameter[0]==0.25}0.09{elsif nozzle_diameter[0]==0.3}0.065{else}0{endif} ; Filament gcode\n{endif}"
  ],
  "filament_cooling_moves": [
    "1"
  ],
  "filament_loading_speed": [
    "14"
  ],
  "filament_unloading_speed": [
    "20"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 110 5.32258 5.45161 5.67742 6 6.48387 7.12903 7.90323 8.70968 9.3871 9.83871 10.0968 10.2258| 0.05 5.30967 0.45 5.50967 0.95 6.1871 1.45 7.39677 1.95 9.05484 2.45 10 2.95 10.3098 3.45 13.0839 3.95 7.6 4.45 7.6 4.95 7.6",
    ""
  ],
  "filament_cooling_final_speed": [
    "2"
  ],
  "filament_loading_speed_start": [
    "19"
  ],
  "compatible_printers_condition": [
    "nozzle_diameter[0]!=0.8 and nozzle_diameter[0]!=0.25 and printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material"
  ],
  "filament_max_volumetric_speed": [
    "11"
  ],
  "filament_cooling_initial_speed": [
    "3"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "20"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_type": [
    "ASA"
  ],
  "hot_plate_temp": [
    "110"
  ],
  "bridge_fan_speed": [
    "30"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "filament_spool_weight": [
    "278"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_infill_max_crossing_speed": [
    "140"
  ],
  "renamed_from": [
    "Prusament ASA @MMU2"
  ],
  "name": "Prusament ASA @MMU",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 11:12