*PLA08PG*

Raw resolved JSON

{
  "idle_temperature": [
    "70"
  ],
  "filament_load_time": [
    "10.5"
  ],
  "filament_unload_time": [
    "8.5"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "slow_down_layer_time": [
    "18"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK4IS|XLIS|MK4S|MK3.9S|COREONE).*/}\nM900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.07{elsif nozzle_diameter[filament_extruder_id]==0.35}0.06{elsif nozzle_diameter[filament_extruder_id]==0.6}0.03{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.8}0.015{else}0{endif} ; Legacy LA\n{else}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.036{elsif nozzle_diameter[filament_extruder_id]==0.5}0.025{elsif nozzle_diameter[filament_extruder_id]==0.6}0.022{elsif nozzle_diameter[filament_extruder_id]==0.8}0.014{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.08{else}0{endif} ; Pressure advance\n{endif}\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_travel_slope": [
    "1"
  ],
  "cooling_slowdown_logic": [
    "consistent_surface"
  ],
  "filament_cooling_moves": [
    "2"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "filament_travel_max_lift": [
    "0.6"
  ],
  "filament_unloading_speed": [
    "40"
  ],
  "filament_infill_max_speed": [
    "0"
  ],
  "filament_purge_multiplier": [
    "81.25%"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_ramming_parameters": [
    "250 100 40.1613 40.3548 40.4516 40.3548 40.2581| 0.05 40.1483 0.45 40.3419 0.95 40.3419 1.45 40.3419 1.95 40.3419 2.45 40.3419 2.95 40.3419 3.45 40.3419 3.95 40.3419 4.45 40.3419 4.95 40.3419"
  ],
  "filament_cooling_final_speed": [
    "3.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "filament_travel_ramping_lift": [
    "1"
  ],
  "compatible_printers_condition": [
    "printer_model=~/(MK4|MK4IS|MK4ISMMU3|MK3.9|MK3.9MMU3)/ and nozzle_diameter[0]==0.8 and ! nozzle_high_flow[0]"
  ],
  "filament_cooling_initial_speed": [
    "10"
  ],
  "filament_unloading_speed_start": [
    "30"
  ],
  "filament_stamping_loading_speed": [
    "29"
  ],
  "filament_infill_max_crossing_speed": [
    "0"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "cooling_perimeter_transition_distance": [
    "10"
  ],
  "filament_max_volumetric_speed": [
    "19"
  ],
  "name": "*PLA08PG*",
  "filament_settings_id": [
    "*PLA08PG*"
  ],
  "type": "filament"
}