FormFutura Centaur PP

FormFutura · PP · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

FormFutura Centaur PP

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

*PC*

Inherited from this (4)

Settings

Basic information

Material variant: PP overridden
Vendor: FormFutura overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 0.89 overridden
was 0 (inherited)
Cost (/kg): 70 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 235 overridden
Nozzle (other layers) (°C): 235 overridden

Cooling

Fan minimum (%): 70 overridden
Fan maximum (%): 70 overridden
Disable fan for first N layers: 2 overridden
Full fan if layer below (sec): 100 overridden
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1.05 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 4 overridden
was 0 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	85 overridden	85 overridden

Other settings

bridge fan speed: 100 overridden
compatible printers condition: nozzle_diameter[0]>=0.35 and printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material) overridden
was printer_notes=~/.*PRINTER_MODEL_VORON.*/ (inherited)
cooling: 1 overridden
was 1 (inherited)
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 overridden
filament colour: #DEE0E6 overridden
was #FF3232 (inherited)
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract lift: 0 overridden
filament soluble: 0 inherited
filament spool weight: 212 overridden
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: 0 overridden
start filament gcode: {if printer_notes!~/.*(MK3.5|MINIIS).*/} M900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.07{endif} ; Filament gcode LA 1.5 {if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0 {endif} {if printer_notes=~/.*MINIIS.*/} M572 S{if nozzle_diameter[0]==0.6}0.2{elsif nozzle_diameter[0]==0.8}0.09{elsif nozzle_diameter[0]==0.4}0.35{elsif nozzle_diameter[0]==0.25}0.98{else}0{endif} {endif} {if printer_notes=~/.*MK3.5.*/} M572 S{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.6}0.022{elsif nozzle_diameter[0]==0.8}0.016{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.09{else}0{endif} ; Filament gcode {endif} via *PC*

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "70"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#DEE0E6"
  ],
  "filament_vendor": [
    "FormFutura"
  ],
  "filament_density": [
    "0.89"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1.05"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "{if printer_notes!~/.*(MK3.5|MINIIS).*/}\nM900 K{if printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.6}0.12{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/ and nozzle_diameter[0]==0.8}0.06{elsif printer_notes=~/.*PRINTER_MODEL_MINI.*/}0.2{elsif nozzle_diameter[0]==0.8}0.02{elsif nozzle_diameter[0]==0.6}0.04{else}0.07{endif} ; Filament gcode LA 1.5\n{if printer_notes=~/.*PRINTER_MODEL_MINI.*/};{elsif printer_notes=~/.*PRINTER_HAS_BOWDEN.*/}M900 K200{elsif nozzle_diameter[0]==0.6}M900 K24{elsif nozzle_diameter[0]==0.8};{else}M900 K45{endif} ; Filament gcode LA 1.0\n{endif}\n\n{if printer_notes=~/.*MINIIS.*/}\nM572 S{if nozzle_diameter[0]==0.6}0.2{elsif nozzle_diameter[0]==0.8}0.09{elsif nozzle_diameter[0]==0.4}0.35{elsif nozzle_diameter[0]==0.25}0.98{else}0{endif}\n{endif}\n\n{if printer_notes=~/.*MK3.5.*/}\nM572 S{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.6}0.022{elsif nozzle_diameter[0]==0.8}0.016{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.09{else}0{endif} ; Filament gcode\n{endif}"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "nozzle_diameter[0]>=0.35 and printer_notes!~/.*MINI.*/ and printer_notes!~/.*PG.*/ and ! (printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK(2.5|3).*/ and single_extruder_multi_material)"
  ],
  "filament_max_volumetric_speed": [
    "4"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "70"
  ],
  "fan_min_speed": [
    "70"
  ],
  "filament_type": [
    "PP"
  ],
  "filament_wipe": [
    "0"
  ],
  "hot_plate_temp": [
    "85"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "235"
  ],
  "filament_retract_lift": [
    "0"
  ],
  "filament_spool_weight": [
    "212"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "hot_plate_temp_initial_layer": [
    "85"
  ],
  "nozzle_temperature_initial_layer": [
    "235"
  ],
  "name": "FormFutura Centaur PP",
  "type": "filament"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 12:03
v1 created 2026-05-19 11:08