mycusini 3D Choco @MC2.0

Print4Taste · GLAZE · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Settings

Basic information

Material variant: GLAZE overridden
Vendor: Print4Taste overridden
Diameter (mm): 18 overridden
Density (g/cm³): 1.26 overridden

Print temperature

Nozzle (initial layer) (°C): 0 overridden
Nozzle (other layers) (°C): 0 overridden

Cooling

Fan minimum (%): 0 overridden
Fan maximum (%): 0 overridden
Disable fan for first N layers: 0 overridden
Full fan if layer below (sec): 60 overridden
Slow down if layer below (sec): 15 overridden
Min speed when slowed (mm/s): 9 overridden

Flow

Flow ratio: 0.95 overridden
Max volumetric speed (mm³/s): 8 overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	0 overridden	0 overridden

Other settings

bridge fan speed: 0 overridden
compatible printers condition: printer_notes=~/.*PRINT4TASTE.*/ and printer_notes=~/.*MYCUSINI2.0.*/ overridden
cooling: 1 overridden
fan always on: 0 overridden
filament colour: #F4A6FF overridden
filament notes: Full cartridge: 18 x 100 mm, 32g Density: 1.26 g/cm3 Cut cartrige size: 18 x ~50 mm, 16g Mycusini 2.0 does not require temperature control in gcode Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile. PRINTER_VENDOR_PRINT4TASTE PRINTER_MODEL_MYCUSINI2.0 overridden
filament retract layer change: 1 overridden
filament retract length: 0.3 overridden
filament retract lift: 1 overridden
filament wipe: 1 overridden
ilament retract before wipe: 30% overridden

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "0"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_type": [
    "GLAZE"
  ],
  "filament_wipe": [
    "1"
  ],
  "filament_notes": [
    "Full cartridge: 18 x 100 mm, 32g\nDensity: 1.26 g/cm3\nCut cartrige size: 18 x ~50 mm, 16g\nMycusini 2.0 does not require temperature control in gcode\n\n\nDon't remove the following keywords! These keywords are used in the \"compatible printer\" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRINT4TASTE\nPRINTER_MODEL_MYCUSINI2.0"
  ],
  "hot_plate_temp": [
    "0"
  ],
  "filament_colour": [
    "#F4A6FF"
  ],
  "filament_vendor": [
    "Print4Taste"
  ],
  "bridge_fan_speed": [
    "0"
  ],
  "filament_density": [
    "1.26"
  ],
  "filament_diameter": [
    "18"
  ],
  "end_filament_gcode": [
    ""
  ],
  "nozzle_temperature": [
    "0"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "9"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    ""
  ],
  "filament_retract_lift": [
    "1"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "filament_retract_length": [
    "0.3"
  ],
  "ilament_retract_before_wipe": [
    "30%"
  ],
  "close_fan_the_first_x_layers": [
    "0"
  ],
  "hot_plate_temp_initial_layer": [
    "0"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINT4TASTE.*/ and printer_notes=~/.*MYCUSINI2.0.*/"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "filament_retract_layer_change": [
    "1"
  ],
  "nozzle_temperature_initial_layer": [
    "0"
  ],
  "name": "mycusini 3D Choco @MC2.0",
  "filament_settings_id": [
    "mycusini 3D Choco @MC2.0"
  ],
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:32