Generic ABS @AQI

Generic · ABS · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*DQ2 0.4*

→

*AQI 0.4*

→

Generic ABS @AQI

Inherited from this (7)

Settings

Basic information

Material variant: ABS overridden
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 overridden
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 255 overridden
Nozzle (other layers) (°C): 255 overridden

Cooling

Fan minimum (%): 80 overridden
Fan maximum (%): 100 overridden
Disable fan for first N layers: 3 overridden
was 3 (inherited)
Full fan if layer below (sec): 20 overridden
Slow down if layer below (sec): 5 overridden
Min speed when slowed (mm/s): 10 overridden

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 8 overridden
was 15 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 overridden	100 overridden

Other settings

bridge fan speed: 100 overridden
compatible printers condition: printer_notes=~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes=~/.*PRINTER_MODEL_AQI.*/ and nozzle_diameter[0]==0.4 inherited
cooling: 1 overridden
fan always on: 1 overridden
filament colour: #EC626F inherited
filament deretract speed: nil overridden
filament load time: 0 overridden
filament loading speed: 28 overridden
filament loading speed start: 3 overridden
filament minimal purge on wipe tower: 15 inherited
filament notes: CU inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before travel: 3 overridden
filament retract before wipe: 70% overridden
filament retract layer change: 1 overridden
filament retract length: 4.1 overridden
filament retract lift: 0.2 overridden
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract restart extra: nil overridden
filament retract speed: 25 overridden
filament soluble: 0 overridden
was 0 (inherited)
filament spool weight: 0 overridden
was 250 (inherited)
filament toolchange delay: 0 inherited
filament wipe: 1 overridden
full fan speed layer: 0 overridden
renamed from: AzteQ Industrial - ABS - Generic overridden
start filament gcode: ; FILAMENT_START_GCODE M191 S75 ; Wait for chamber temperature overridden

Raw resolved JSON

{
  "filament_cost": [
    "0"
  ],
  "filament_notes": [
    "CU"
  ],
  "filament_colour": [
    "#EC626F"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_spool_weight": [
    "0"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_VENDOR_TRILAB.*/ and printer_notes=~/.*PRINTER_MODEL_AQI.*/ and nozzle_diameter[0]==0.4"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "cooling": [
    "1"
  ],
  "renamed_from": [
    "AzteQ Industrial - ABS - Generic"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "80"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "1"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_load_time": [
    "0"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "start_filament_gcode": [
    "; FILAMENT_START_GCODE\nM191 S75 ; Wait for chamber temperature"
  ],
  "filament_retract_lift": [
    "0.2"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_retract_speed": [
    "25"
  ],
  "filament_retract_length": [
    "4.1"
  ],
  "filament_deretract_speed": [
    "nil"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "filament_retract_before_wipe": [
    "70%"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_layer_change": [
    "1"
  ],
  "filament_retract_before_travel": [
    "3"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "255"
  ],
  "name": "Generic ABS @AQI",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:32