PunkFil PETG @RatRig
RatRig · PETG
· by prusa-system
· 0 downloads
Settings
Basic information
- Material variant
-
PETG overridden
- Vendor
-
RatRig overridden
- Diameter (mm)
-
1.75 overridden
- Density (g/cm³)
-
1.27 overridden
- Cost (/kg)
-
24.5 overridden
Print temperature
- Nozzle (initial layer) (°C)
-
235 overridden
- Nozzle (other layers) (°C)
-
235 overridden
Cooling
- Fan minimum (%)
-
40 overridden
- Fan maximum (%)
-
80 overridden
- Disable fan for first N layers
-
3 overridden
- Full fan if layer below (sec)
-
6 overridden
- Slow down if layer below (sec)
-
4 overridden
- Min speed when slowed (mm/s)
-
20 overridden
Flow
- Flow ratio
-
0.93 overridden
- Max volumetric speed (mm³/s)
-
40 overridden
Bed temperature
| Plate | Initial layer (°C) | Other layers (°C) |
|---|---|---|
| High Temp Plate |
80
overridden
|
80
overridden
|
Other settings
- bridge fan speed
-
60 overridden
- cooling
-
1 overridden
- end filament gcode
-
, Filament-specific end gcode \n, END gcode for filament\n" overridden
- fan always on
-
1 overridden
- filament colour
-
#ceff00 overridden
- filament enable toolchange part fan
-
0 overridden
- filament enable toolchange temp
-
0 overridden
- filament load time
-
0 overridden
- filament loading speed
-
28 overridden
- filament loading speed start
-
3 overridden
- filament max speed
-
0 overridden
- filament minimal purge on wipe tower
-
15 overridden
- filament ramming parameters
-
120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
- filament retract layer change
-
1 overridden
- filament retract length
-
0.8 overridden
- filament soluble
-
0 overridden
- filament spool weight
-
0 overridden
- filament unload time
-
0 overridden
- filament unloading speed
-
90 overridden
- filament unloading speed start
-
100 overridden
- filament wipe
-
nil overridden
- full fan speed layer
-
0 overridden
- start filament gcode
-
;Filament gcode SET_PRESSURE_ADVANCE ADVANCE=0.026 overridden
Raw resolved JSON
{
"cooling": [
"1"
],
"fan_always_on": [
"1"
],
"fan_max_speed": [
"80"
],
"fan_min_speed": [
"40"
],
"filament_cost": [
"24.5"
],
"filament_type": [
"PETG"
],
"filament_wipe": [
"nil"
],
"filament_notes": [
""
],
"hot_plate_temp": [
"80"
],
"filament_colour": [
"#ceff00"
],
"filament_vendor": [
"RatRig"
],
"bridge_fan_speed": [
"60"
],
"filament_density": [
"1.27"
],
"filament_soluble": [
"0"
],
"filament_diameter": [
"1.75"
],
"end_filament_gcode": [
"",
"Filament-specific end gcode \\n",
"END gcode for filament\\n\""
],
"filament_load_time": [
"0"
],
"filament_max_speed": [
"0"
],
"nozzle_temperature": [
"235"
],
"filament_flow_ratio": [
"0.93"
],
"slow_down_min_speed": [
"20"
],
"filament_settings_id": [
""
],
"filament_unload_time": [
"0"
],
"full_fan_speed_layer": [
"0"
],
"slow_down_layer_time": [
"4"
],
"start_filament_gcode": [
";Filament gcode\nSET_PRESSURE_ADVANCE ADVANCE=0.026"
],
"filament_spool_weight": [
"0"
],
"fan_cooling_layer_time": [
"6"
],
"filament_loading_speed": [
"28"
],
"filament_retract_length": [
"0.8"
],
"filament_unloading_speed": [
"90"
],
"filament_ramming_parameters": [
"120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
],
"close_fan_the_first_x_layers": [
"3"
],
"filament_loading_speed_start": [
"3"
],
"hot_plate_temp_initial_layer": [
"80"
],
"filament_max_volumetric_speed": [
"40"
],
"filament_retract_layer_change": [
"1"
],
"filament_unloading_speed_start": [
"100"
],
"filament_enable_toolchange_temp": [
"0"
],
"nozzle_temperature_initial_layer": [
"235"
],
"filament_enable_toolchange_part_fan": [
"0"
],
"filament_minimal_purge_on_wipe_tower": [
"15"
],
"name": "PunkFil PETG @RatRig",
"type": "filament"
}
Version history
View full history with diffs →- v1 created 2026-05-19 05:18