Eolas Prints PETG @MEGA

Eolas Prints · PETG · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common_mega*

→

*PETG_mega*

→

Eolas Prints PETG @MEGA

Inherited from this (1)

Eolas Prints PETG - UV Resistant @MEGA

Settings

Basic information

Material variant: PETG inherited
Vendor: Eolas Prints overridden
was Generic (inherited)
Density (g/cm³): 1.27 overridden
was 1.27 (inherited)
Cost (/kg): 29.90 overridden
was 27.82 (inherited)

Print temperature

Nozzle (initial layer) (°C): 235 overridden
was 230 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 30 inherited
Fan maximum (%): 50 inherited
Full fan if layer below (sec): 20 inherited
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Max volumetric speed (mm³/s): 8 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	85 overridden was 90	90 overridden was 90

Other settings

bridge fan speed: 50 inherited
compatible printers condition: printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_I3_MEGA.*/ inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #4D9398 overridden
was #FF8000 (inherited)
filament spool weight: 0 overridden

Raw resolved JSON

{
  "fan_always_on": [
    "1"
  ],
  "filament_vendor": [
    "Eolas Prints"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_VENDOR_ANYCUBIC.*/ and printer_notes=~/.*PRINTER_MODEL_I3_MEGA.*/"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "29.90"
  ],
  "filament_type": [
    "PETG"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "filament_colour": [
    "#4D9398"
  ],
  "bridge_fan_speed": [
    "50"
  ],
  "filament_density": [
    "1.27"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "hot_plate_temp_initial_layer": [
    "85"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "nozzle_temperature_initial_layer": [
    "235"
  ],
  "filament_spool_weight": [
    "0"
  ],
  "name": "Eolas Prints PETG @MEGA",
  "filament_settings_id": [
    "Eolas Prints PETG @MEGA"
  ],
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:17