Prusament PETG @MEGA0

Prusa · PETG · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common_mega0*

→

*PET_mega0*

→

Prusament PETG @MEGA0

Settings

Basic information

Material variant: PETG inherited
Vendor: Prusa Polymers overridden
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 overridden
was 1.27 (inherited)
Cost (/kg): 24.99 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 245 overridden
was 240 (inherited)
Nozzle (other layers) (°C): 245 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 20 inherited
Fan maximum (%): 50 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 20 inherited
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 8 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	70 inherited	70 overridden was 70

Other settings

bridge fan speed: 100 inherited
compatible printers condition: printer_model=="MEGA0" inherited
cooling: 1 inherited
fan always on: 1 inherited
filament colour: #FF8000 inherited
filament soluble: 0 inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "24.99"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "compatible_printers_condition": [
    "printer_model==\"MEGA0\""
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_type": [
    "PETG"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "filament_colour": [
    "#FF8000"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "245"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "filament_vendor": [
    "Prusa Polymers"
  ],
  "name": "Prusament PETG @MEGA0",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:17