slicershare (test)
← Generic ABS @BBL P2S

History of Generic ABS @BBL P2S

Direct edits to this profile, and edits to any profile it inherits from. An inherited change can shift this profile's effective behavior even when this profile itself wasn't touched.

Inherits from: fdm_filament_common → fdm_filament_abs → Generic ABS @base
  1. via parent v13 of fdm_filament_common — updated
    2026-05-19 04:18
    Settings (2)
    • filament z hop types removed nil
    • slow down layer time 8 → 5
  2. via parent v14 of fdm_filament_abs — updated
    2026-05-19 04:18
    Settings (88)
    • activate air filtration removed 0
    • additional cooling fan speed removed 0
    • chamber temperatures removed 0
    • circle compensation speed removed 200
    • compatible printers removed —
    • complete print exhaust fan speed removed 70
    • cool plate temp 105 → 95
    • cool plate temp initial layer 105 → 95
    • cooling perimeter transition distance removed 10
    • cooling slowdown logic removed uniform_cooling
    • counter coef 1 removed 0
    • counter coef 2 removed 0.008
    • counter coef 3 removed -0.041
    • counter limit max removed 0.033
    • counter limit min removed -0.035
    • diameter limit removed 50
    • during print exhaust fan speed removed 70
    • eng plate temp 105 → 95
    • eng plate temp initial layer 105 → 95
    • filament adaptive volumetric speed removed 0
    • filament bridge speed removed 25
    • filament change length removed 10
    • filament cooling before tower removed 0
    • filament dev ams drying ams limitations removed 1
    • filament dev ams drying heat distortion temperature removed 45.0
    • filament dev ams drying temperature removed 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time removed 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature removed 90.0
    • filament dev chamber drying time removed 12.0
    • filament dev drying cooling temperature removed 35.0
    • filament dev drying softening temperature removed 40.0
    • filament enable overhang speed removed 1
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode
    • filament extruder compatibility removed 0
    • filament extruder variant removed Direct Drive Standard
    • filament flush temp removed 0
    • filament flush volumetric speed removed 0
    • filament long retractions when cut removed nil
    • filament long retractions when ec removed nil
    • filament metal stickiness removed None
    • filament overhang 1 4 speed removed 0
    • filament overhang 2 4 speed removed 50
    • filament overhang 3 4 speed removed 30
    • filament overhang 4 4 speed removed 10
    • filament overhang totally speed removed 10
    • filament pre cooling temperature removed 0
    • filament pre cooling temperature nc removed 0
    • filament prime volume removed 45
    • filament prime volume nc removed 60
    • filament printable removed 3
    • filament ramming travel time removed 0
    • filament ramming travel time nc removed 0
    • filament ramming volumetric speed removed -1
    • filament ramming volumetric speed nc removed -1
    • filament retract length nc removed 14
    • filament retraction distances when cut removed nil
    • filament retraction distances when ec removed nil
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament shrink removed 100%
    • filament start gcode ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif} → ; Filament gcode
    • filament tower interface pre extrusion dist removed 10
    • filament tower interface pre extrusion length removed 0
    • filament tower interface print temp removed -1
    • filament tower interface purge volume removed 20
    • filament tower ironing area removed 4
    • filament velocity adaptation factor removed 1
    • hole coef 1 removed 0
    • hole coef 2 removed -0.008
    • hole coef 3 removed 0.23415
    • hole limit max removed 0.22
    • hole limit min removed 0.088
    • hot plate temp 105 → 95
    • hot plate temp initial layer 105 → 95
    • impact strength z removed 10
    • long retractions when ec removed 0
    • no slow down for cooling on outwalls removed 0
    • nozzle temperature 260 → 240
    • nozzle temperature initial layer 260 → 240
    • override process overhang speed removed 0
    • retraction distances when ec removed 0
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
    • textured plate temp removed 60
    • textured plate temp initial layer removed 60
    • volumetric speed coefficients removed 0 0 0 0 0 0
  3. via parent v12 of fdm_filament_common — updated
    2026-05-19 04:18
    Settings (82)
    • activate air filtration removed 0
    • additional cooling fan speed removed 0
    • chamber temperatures removed 0
    • circle compensation speed removed 200
    • compatible printers removed —
    • complete print exhaust fan speed removed 70
    • cooling perimeter transition distance removed 10
    • cooling slowdown logic removed uniform_cooling
    • counter coef 1 removed 0
    • counter coef 2 removed 0.008
    • counter coef 3 removed -0.041
    • counter limit max removed 0.033
    • counter limit min removed -0.035
    • diameter limit removed 50
    • during print exhaust fan speed removed 70
    • filament adaptive volumetric speed removed 0
    • filament bridge speed removed 25
    • filament change length removed 10
    • filament cooling before tower removed 0
    • filament dev ams drying ams limitations removed 1
    • filament dev ams drying heat distortion temperature removed 45.0
    • filament dev ams drying temperature removed 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time removed 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature removed 90.0
    • filament dev chamber drying time removed 12.0
    • filament dev drying cooling temperature removed 35.0
    • filament dev drying softening temperature removed 40.0
    • filament enable overhang speed removed 1
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode
    • filament extruder compatibility removed 0
    • filament extruder variant removed Direct Drive Standard
    • filament flush temp removed 0
    • filament flush volumetric speed removed 0
    • filament long retractions when cut removed nil
    • filament long retractions when ec removed nil
    • filament metal stickiness removed None
    • filament overhang 1 4 speed removed 0
    • filament overhang 2 4 speed removed 50
    • filament overhang 3 4 speed removed 30
    • filament overhang 4 4 speed removed 10
    • filament overhang totally speed removed 10
    • filament pre cooling temperature removed 0
    • filament pre cooling temperature nc removed 0
    • filament prime volume removed 45
    • filament prime volume nc removed 60
    • filament printable removed 3
    • filament ramming travel time removed 0
    • filament ramming travel time nc removed 0
    • filament ramming volumetric speed removed -1
    • filament ramming volumetric speed nc removed -1
    • filament retract length nc removed 14
    • filament retraction distances when cut removed nil
    • filament retraction distances when ec removed nil
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament shrink removed 100%
    • filament start gcode ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif} → ; Filament gcode
    • filament tower interface pre extrusion dist removed 10
    • filament tower interface pre extrusion length removed 0
    • filament tower interface print temp removed -1
    • filament tower interface purge volume removed 20
    • filament tower ironing area removed 4
    • filament velocity adaptation factor removed 1
    • hole coef 1 removed 0
    • hole coef 2 removed -0.008
    • hole coef 3 removed 0.23415
    • hole limit max removed 0.22
    • hole limit min removed 0.088
    • impact strength z removed 10
    • long retractions when ec removed 0
    • no slow down for cooling on outwalls removed 0
    • nozzle temperature range high removed 240
    • nozzle temperature range low removed 190
    • override process overhang speed removed 0
    • retraction distances when ec removed 0
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
    • textured plate temp removed 60
    • textured plate temp initial layer removed 60
    • volumetric speed coefficients removed 0 0 0 0 0 0
  4. via parent v13 of fdm_filament_abs — updated
    2026-05-19 04:18
    Settings (91)
    • activate air filtration 1 → 0
    • additional cooling fan speed added 0
    • chamber temperatures added 0
    • circle compensation speed added 200
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • cool plate temp 0 → 105
    • cool plate temp initial layer 0 → 105
    • cooling perimeter transition distance added 10
    • cooling slowdown logic added uniform_cooling
    • counter coef 1 added 0
    • counter coef 2 added 0.008
    • counter coef 3 added -0.041
    • counter limit max added 0.033
    • counter limit min added -0.035
    • diameter limit added 50
    • during print exhaust fan speed added 70
    • eng plate temp 90 → 105
    • eng plate temp initial layer 90 → 105
    • filament adaptive volumetric speed added 0
    • filament adhesiveness category removed 200
    • filament bridge speed added 25
    • filament change length added 10
    • filament cooling before tower added 0
    • filament dev ams drying ams limitations added 1
    • filament dev ams drying heat distortion temperature 90 → 45.0
    • filament dev ams drying temperature 65, 80, 65, 75 → 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time 12, 8.0, 12, 8.0 → 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature added 90.0
    • filament dev chamber drying time added 12.0
    • filament dev drying cooling temperature 75 → 35.0
    • filament dev drying softening temperature 80 → 40.0
    • filament enable overhang speed added 1
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament extruder compatibility added 0
    • filament extruder variant added Direct Drive Standard
    • filament flush temp added 0
    • filament flush volumetric speed added 0
    • filament long retractions when cut added nil
    • filament long retractions when ec added nil
    • filament metal stickiness added None
    • filament overhang 1 4 speed added 0
    • filament overhang 2 4 speed added 50
    • filament overhang 3 4 speed added 30
    • filament overhang 4 4 speed added 10
    • filament overhang totally speed added 10
    • filament pre cooling temperature added 0
    • filament pre cooling temperature nc added 0
    • filament prime volume added 45
    • filament prime volume nc added 60
    • filament printable added 3
    • filament ramming travel time added 0
    • filament ramming travel time nc added 0
    • filament ramming volumetric speed added -1
    • filament ramming volumetric speed nc added -1
    • filament retract length nc added 14
    • filament retraction distances when cut added nil
    • filament retraction distances when ec added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • filament start gcode ; Filament gcode → ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • filament tower interface pre extrusion dist added 10
    • filament tower interface pre extrusion length added 0
    • filament tower interface print temp added -1
    • filament tower interface purge volume added 20
    • filament tower ironing area added 4
    • filament velocity adaptation factor added 1
    • hole coef 1 added 0
    • hole coef 2 added -0.008
    • hole coef 3 added 0.23415
    • hole limit max added 0.22
    • hole limit min added 0.088
    • hot plate temp 90 → 105
    • hot plate temp initial layer 90 → 105
    • impact strength z added 10
    • long retractions when ec added 0
    • no slow down for cooling on outwalls added 0
    • nozzle temperature 270 → 260
    • nozzle temperature range high 280 → 270
    • override process overhang speed added 0
    • retraction distances when ec added 0
    • slow down min speed 20 → 10
    • supertack plate temp 0 → 45
    • supertack plate temp initial layer 0 → 45
    • temperature vitrification 100 → 110
    • textured plate temp 90 → 60
    • textured plate temp initial layer 90 → 60
    • volumetric speed coefficients added 0 0 0 0 0 0
  5. via parent v11 of fdm_filament_common — updated
    2026-05-19 04:17
    Settings (80)
    • activate air filtration added 0
    • additional cooling fan speed added 0
    • chamber temperatures added 0
    • circle compensation speed added 200
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • cooling perimeter transition distance added 10
    • cooling slowdown logic added uniform_cooling
    • counter coef 1 added 0
    • counter coef 2 added 0.008
    • counter coef 3 added -0.041
    • counter limit max added 0.033
    • counter limit min added -0.035
    • diameter limit added 50
    • during print exhaust fan speed added 70
    • filament adaptive volumetric speed added 0
    • filament bridge speed added 25
    • filament change length added 10
    • filament cooling before tower added 0
    • filament dev ams drying ams limitations added 1
    • filament dev ams drying heat distortion temperature added 45.0
    • filament dev ams drying temperature added 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time added 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature added 90.0
    • filament dev chamber drying time added 12.0
    • filament dev drying cooling temperature added 35.0
    • filament dev drying softening temperature added 40.0
    • filament enable overhang speed added 1
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament extruder compatibility added 0
    • filament extruder variant added Direct Drive Standard
    • filament flush temp added 0
    • filament flush volumetric speed added 0
    • filament long retractions when cut added nil
    • filament long retractions when ec added nil
    • filament metal stickiness added None
    • filament overhang 1 4 speed added 0
    • filament overhang 2 4 speed added 50
    • filament overhang 3 4 speed added 30
    • filament overhang 4 4 speed added 10
    • filament overhang totally speed added 10
    • filament pre cooling temperature added 0
    • filament pre cooling temperature nc added 0
    • filament prime volume added 45
    • filament prime volume nc added 60
    • filament printable added 3
    • filament ramming travel time added 0
    • filament ramming travel time nc added 0
    • filament ramming volumetric speed added -1
    • filament ramming volumetric speed nc added -1
    • filament retract length nc added 14
    • filament retraction distances when cut added nil
    • filament retraction distances when ec added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • filament start gcode ; Filament gcode → ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • filament tower interface pre extrusion dist added 10
    • filament tower interface pre extrusion length added 0
    • filament tower interface print temp added -1
    • filament tower interface purge volume added 20
    • filament tower ironing area added 4
    • filament velocity adaptation factor added 1
    • hole coef 1 added 0
    • hole coef 2 added -0.008
    • hole coef 3 added 0.23415
    • hole limit max added 0.22
    • hole limit min added 0.088
    • impact strength z added 10
    • long retractions when ec added 0
    • no slow down for cooling on outwalls added 0
    • nozzle temperature range high added 240
    • nozzle temperature range low added 190
    • override process overhang speed added 0
    • retraction distances when ec added 0
    • supertack plate temp added 45
    • supertack plate temp initial layer added 45
    • volumetric speed coefficients added 0 0 0 0 0 0
  6. via parent v12 of fdm_filament_abs — updated
    2026-05-19 04:16
    Settings (24)
    • activate air filtration added 1
    • cool plate temp 105 → 0
    • cool plate temp initial layer 105 → 0
    • eng plate temp 105 → 90
    • eng plate temp initial layer 105 → 90
    • fan max speed 35 → 80
    • fan min speed 35 → 10
    • filament adhesiveness category added 200
    • filament dev ams drying heat distortion temperature added 90
    • filament dev ams drying temperature added 65, 80, 65, 75
    • filament dev ams drying time added 12, 8.0, 12, 8.0
    • filament dev drying cooling temperature added 75
    • filament dev drying softening temperature added 80
    • filament end gcode ; filament end gcode → ; filament end gcode
    • hot plate temp 105 → 90
    • hot plate temp initial layer 105 → 90
    • nozzle temperature 260 → 270
    • nozzle temperature range high 270 → 280
    • slow down min speed 10 → 20
    • supertack plate temp added 0
    • supertack plate temp initial layer added 0
    • temperature vitrification 110 → 100
    • textured plate temp 105 → 90
    • textured plate temp initial layer 105 → 90
  7. via parent v2 of Generic ABS @base — updated
    2026-05-19 04:16
    Settings (17)
    • cool plate temp 80 → 105
    • cool plate temp initial layer 80 → 105
    • eng plate temp 80 → 105
    • eng plate temp initial layer 80 → 105
    • fan max speed 5 → 35
    • fan min speed 5 → 35
    • filament density 1.10 → 1.04
    • filament diameter 2.85 → 1.75
    • hot plate temp 80 → 105
    • hot plate temp initial layer 80 → 105
    • nozzle temperature 235 → 260
    • nozzle temperature initial layer 240 → 260
    • nozzle temperature range high 240 → 270
    • nozzle temperature range low 235 → 240
    • slow down layer time 15 → 3
    • textured plate temp 80 → 105
    • textured plate temp initial layer 80 → 105
  8. direct edit v1 — created
    2026-05-19 04:15
    Profile created at this point. No prior version to diff against.
  9. via parent v11 of fdm_filament_abs — updated
    2026-05-19 04:14
    Settings (15)
    • cool plate temp 100 → 105
    • cool plate temp initial layer 100 → 105
    • eng plate temp 100 → 105
    • eng plate temp initial layer 100 → 105
    • fan max speed 0 → 35
    • fan min speed 0 → 35
    • filament max volumetric speed 11 → 28.6
    • hot plate temp 100 → 105
    • hot plate temp initial layer 100 → 105
    • nozzle temperature 245 → 260
    • nozzle temperature initial layer 180 → 260
    • nozzle temperature range high 245 → 270
    • overhang fan speed 30 → 80
    • textured plate temp 100 → 105
    • textured plate temp initial layer 100 → 105
  10. via parent v10 of fdm_filament_abs — updated
    2026-05-19 04:14
    Settings (17)
    • bed type removed Cool Plate
    • cool plate temp 105 → 100
    • cool plate temp initial layer 105 → 100
    • eng plate temp 105 → 100
    • eng plate temp initial layer 105 → 100
    • fan max speed 80 → 0
    • fan min speed 10 → 0
    • filament max volumetric speed 28.6 → 11
    • filament z hop types added nil
    • hot plate temp 105 → 100
    • hot plate temp initial layer 105 → 100
    • nozzle temperature 260 → 245
    • nozzle temperature initial layer 260 → 180
    • nozzle temperature range high 270 → 245
    • overhang fan speed 80 → 30
    • textured plate temp 105 → 100
    • textured plate temp initial layer 105 → 100
  11. via parent v10 of fdm_filament_common — updated
    2026-05-19 04:14
    Settings (2)
    • bed type removed Cool Plate
    • filament z hop types added nil
  12. via parent v9 of fdm_filament_abs — updated
    2026-05-19 04:14
    Settings (5)
    • bed type added Cool Plate
    • filament is support added 0
    • filament minimal purge on wipe tower 90 → 15
    • filament z hop types removed nil
    • required nozzle HRC added 3
  13. via parent v9 of fdm_filament_common — updated
    2026-05-19 04:14
    Settings (5)
    • bed type added Cool Plate
    • filament is support added 0
    • filament minimal purge on wipe tower 90 → 15
    • filament z hop types removed nil
    • required nozzle HRC added 3
  14. via parent v8 of fdm_filament_abs — updated
    2026-05-19 04:14
    Identity / metadata
    • Vendor: QIDI → Generic
    Settings (15)
    • activate air filtration removed 1
    • activate chamber temp control removed 0
    • bed type removed Cool Plate
    • compatible printers removed —
    • cool plate temp 0 → 105
    • cool plate temp initial layer 0 → 105
    • during print exhaust fan speed removed 100
    • enable pressure advance removed 1
    • fan max speed 35 → 80
    • fan min speed 35 → 10
    • filament end gcode added ; filament end gcode
    • filament minimal purge on wipe tower 15 → 90
    • filament start gcode added ; Filament gcode
    • filament vendor QIDI → Generic
    • reduce fan stop start freq 0 → 1
  15. via parent v8 of fdm_filament_common — updated
    2026-05-19 04:14
    Identity / metadata
    • Vendor: QIDI → Generic
    Settings (11)
    • activate air filtration removed 1
    • activate chamber temp control removed 0
    • bed type removed Cool Plate
    • compatible printers removed —
    • during print exhaust fan speed removed 100
    • enable pressure advance removed 1
    • filament end gcode added ; filament end gcode
    • filament minimal purge on wipe tower 15 → 90
    • filament start gcode added ; Filament gcode
    • filament vendor QIDI → Generic
    • reduce fan stop start freq 1 → 0
  16. via parent v7 of fdm_filament_abs — updated
    2026-05-19 04:14
    Identity / metadata
    • Vendor: Generic → QIDI
    Settings (30)
    • activate air filtration added 1
    • activate chamber temp control added 0
    • chamber temperatures removed 55
    • compatible printers added —
    • cool plate temp 90 → 0
    • cool plate temp initial layer 90 → 0
    • during print exhaust fan speed added 100
    • enable pressure advance added 1
    • eng plate temp 90 → 105
    • eng plate temp initial layer 90 → 105
    • fan cooling layer time 60 → 30
    • fan max speed 80 → 35
    • fan min speed 10 → 35
    • filament density 1.24 → 1.04
    • filament end gcode removed ; filament end gcode
    • filament is support removed 0
    • filament max volumetric speed 20 → 28.6
    • filament start gcode removed ; Filament gcode
    • filament vendor Generic → QIDI
    • hot plate temp 90 → 105
    • hot plate temp initial layer 90 → 105
    • nozzle temperature 270 → 260
    • nozzle temperature initial layer 250 → 260
    • reduce fan stop start freq 1 → 0
    • required nozzle HRC removed 3
    • slow down layer time 4 → 3
    • slow down min speed 20 → 10
    • temperature vitrification 100 → 110
    • textured plate temp 90 → 105
    • textured plate temp initial layer 90 → 105
  17. via parent v7 of fdm_filament_common — updated
    2026-05-19 04:14
    Identity / metadata
    • Vendor: Generic → QIDI
    Settings (11)
    • activate air filtration added 1
    • activate chamber temp control added 0
    • compatible printers added —
    • during print exhaust fan speed added 100
    • enable pressure advance added 1
    • filament end gcode removed ; filament end gcode
    • filament is support removed 0
    • filament start gcode removed ; Filament gcode
    • filament vendor Generic → QIDI
    • reduce fan stop start freq 0 → 1
    • required nozzle HRC removed 3
  18. via parent v6 of fdm_filament_abs — updated
    2026-05-19 04:14
    Settings (19)
    • bed type added Cool Plate
    • chamber temperatures added 55
    • cool plate temp 105 → 90
    • cool plate temp initial layer 105 → 90
    • eng plate temp 105 → 90
    • eng plate temp initial layer 105 → 90
    • fan cooling layer time 30 → 60
    • filament density 1.04 → 1.24
    • filament diameter 2.85 → 1.75
    • filament max volumetric speed 28.6 → 20
    • hot plate temp 105 → 90
    • hot plate temp initial layer 105 → 90
    • nozzle temperature 260 → 270
    • nozzle temperature initial layer 260 → 250
    • slow down layer time 3 → 4
    • slow down min speed 10 → 20
    • temperature vitrification 110 → 100
    • textured plate temp 105 → 90
    • textured plate temp initial layer 105 → 90
  19. via parent v6 of fdm_filament_common — updated
    2026-05-19 04:14
    Settings (2)
    • bed type added Cool Plate
    • filament diameter 2.85 → 1.75
  20. via parent v5 of fdm_filament_abs — updated
    2026-05-19 04:14
    Settings (19)
    • cool plate temp 80 → 105
    • cool plate temp initial layer 80 → 105
    • eng plate temp 80 → 105
    • eng plate temp initial layer 80 → 105
    • fan max speed 5 → 80
    • fan min speed 5 → 10
    • filament density 1.10 → 1.04
    • filament diameter 1.75 → 2.85
    • filament max volumetric speed 0 → 28.6
    • filament z hop types added nil
    • hot plate temp 80 → 105
    • hot plate temp initial layer 80 → 105
    • nozzle temperature 235 → 260
    • nozzle temperature initial layer 240 → 260
    • nozzle temperature range high 240 → 270
    • nozzle temperature range low 235 → 240
    • slow down layer time 15 → 3
    • textured plate temp 80 → 105
    • textured plate temp initial layer 80 → 105
  21. via parent v5 of fdm_filament_common — updated
    2026-05-19 04:14
    Settings (4)
    • filament diameter 1.75 → 2.85
    • filament z hop types added nil
    • textured plate temp added 60
    • textured plate temp initial layer added 60
  22. via parent v4 of fdm_filament_abs — updated
    2026-05-19 04:14
    Settings (96)
    • activate air filtration removed 0
    • additional cooling fan speed removed 0
    • chamber temperatures removed 0
    • circle compensation speed removed 200
    • compatible printers removed —
    • complete print exhaust fan speed removed 70
    • cool plate temp 105 → 80
    • cool plate temp initial layer 105 → 80
    • cooling perimeter transition distance removed 10
    • cooling slowdown logic removed uniform_cooling
    • counter coef 1 removed 0
    • counter coef 2 removed 0.008
    • counter coef 3 removed -0.041
    • counter limit max removed 0.033
    • counter limit min removed -0.035
    • diameter limit removed 50
    • during print exhaust fan speed removed 70
    • eng plate temp 105 → 80
    • eng plate temp initial layer 105 → 80
    • fan max speed 80 → 5
    • fan min speed 10 → 5
    • filament adaptive volumetric speed removed 0
    • filament bridge speed removed 25
    • filament change length removed 10
    • filament cooling before tower removed 0
    • filament density 1.04 → 1.10
    • filament dev ams drying ams limitations removed 1
    • filament dev ams drying heat distortion temperature removed 45.0
    • filament dev ams drying temperature removed 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time removed 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature removed 90.0
    • filament dev chamber drying time removed 12.0
    • filament dev drying cooling temperature removed 35.0
    • filament dev drying softening temperature removed 40.0
    • filament enable overhang speed removed 1
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode
    • filament extruder compatibility removed 0
    • filament extruder variant removed Direct Drive Standard
    • filament flush temp removed 0
    • filament flush volumetric speed removed 0
    • filament long retractions when cut removed nil
    • filament long retractions when ec removed nil
    • filament max volumetric speed 28.6 → 0
    • filament metal stickiness removed None
    • filament overhang 1 4 speed removed 0
    • filament overhang 2 4 speed removed 50
    • filament overhang 3 4 speed removed 30
    • filament overhang 4 4 speed removed 10
    • filament overhang totally speed removed 10
    • filament pre cooling temperature removed 0
    • filament pre cooling temperature nc removed 0
    • filament prime volume removed 45
    • filament prime volume nc removed 60
    • filament printable removed 3
    • filament ramming travel time removed 0
    • filament ramming travel time nc removed 0
    • filament ramming volumetric speed removed -1
    • filament ramming volumetric speed nc removed -1
    • filament retract length nc removed 14
    • filament retraction distances when cut removed nil
    • filament retraction distances when ec removed nil
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament shrink removed 100%
    • filament start gcode ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif} → ; Filament gcode
    • filament tower interface pre extrusion dist removed 10
    • filament tower interface pre extrusion length removed 0
    • filament tower interface print temp removed -1
    • filament tower interface purge volume removed 20
    • filament tower ironing area removed 4
    • filament velocity adaptation factor removed 1
    • filament z hop types removed nil
    • hole coef 1 removed 0
    • hole coef 2 removed -0.008
    • hole coef 3 removed 0.23415
    • hole limit max removed 0.22
    • hole limit min removed 0.088
    • hot plate temp 105 → 80
    • hot plate temp initial layer 105 → 80
    • impact strength z removed 10
    • long retractions when ec removed 0
    • no slow down for cooling on outwalls removed 0
    • nozzle temperature 260 → 235
    • nozzle temperature initial layer 260 → 240
    • nozzle temperature range high 270 → 240
    • nozzle temperature range low 240 → 235
    • override process overhang speed removed 0
    • retraction distances when ec removed 0
    • slow down layer time 3 → 15
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
    • textured plate temp 60 → 80
    • textured plate temp initial layer 60 → 80
    • volumetric speed coefficients removed 0 0 0 0 0 0
  23. via parent v4 of fdm_filament_common — updated
    2026-05-19 04:14
    Settings (83)
    • activate air filtration removed 0
    • additional cooling fan speed removed 0
    • chamber temperatures removed 0
    • circle compensation speed removed 200
    • compatible printers removed —
    • complete print exhaust fan speed removed 70
    • cooling perimeter transition distance removed 10
    • cooling slowdown logic removed uniform_cooling
    • counter coef 1 removed 0
    • counter coef 2 removed 0.008
    • counter coef 3 removed -0.041
    • counter limit max removed 0.033
    • counter limit min removed -0.035
    • diameter limit removed 50
    • during print exhaust fan speed removed 70
    • filament adaptive volumetric speed removed 0
    • filament bridge speed removed 25
    • filament change length removed 10
    • filament cooling before tower removed 0
    • filament dev ams drying ams limitations removed 1
    • filament dev ams drying heat distortion temperature removed 45.0
    • filament dev ams drying temperature removed 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time removed 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature removed 90.0
    • filament dev chamber drying time removed 12.0
    • filament dev drying cooling temperature removed 35.0
    • filament dev drying softening temperature removed 40.0
    • filament enable overhang speed removed 1
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode
    • filament extruder compatibility removed 0
    • filament extruder variant removed Direct Drive Standard
    • filament flush temp removed 0
    • filament flush volumetric speed removed 0
    • filament long retractions when cut removed nil
    • filament long retractions when ec removed nil
    • filament metal stickiness removed None
    • filament overhang 1 4 speed removed 0
    • filament overhang 2 4 speed removed 50
    • filament overhang 3 4 speed removed 30
    • filament overhang 4 4 speed removed 10
    • filament overhang totally speed removed 10
    • filament pre cooling temperature removed 0
    • filament pre cooling temperature nc removed 0
    • filament prime volume removed 45
    • filament prime volume nc removed 60
    • filament printable removed 3
    • filament ramming travel time removed 0
    • filament ramming travel time nc removed 0
    • filament ramming volumetric speed removed -1
    • filament ramming volumetric speed nc removed -1
    • filament retract length nc removed 14
    • filament retraction distances when cut removed nil
    • filament retraction distances when ec removed nil
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament shrink removed 100%
    • filament start gcode ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif} → ; Filament gcode
    • filament tower interface pre extrusion dist removed 10
    • filament tower interface pre extrusion length removed 0
    • filament tower interface print temp removed -1
    • filament tower interface purge volume removed 20
    • filament tower ironing area removed 4
    • filament velocity adaptation factor removed 1
    • filament z hop types removed nil
    • hole coef 1 removed 0
    • hole coef 2 removed -0.008
    • hole coef 3 removed 0.23415
    • hole limit max removed 0.22
    • hole limit min removed 0.088
    • impact strength z removed 10
    • long retractions when ec removed 0
    • no slow down for cooling on outwalls removed 0
    • nozzle temperature range high removed 240
    • nozzle temperature range low removed 190
    • override process overhang speed removed 0
    • retraction distances when ec removed 0
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
    • textured plate temp removed 60
    • textured plate temp initial layer removed 60
    • volumetric speed coefficients removed 0 0 0 0 0 0
  24. via parent v3 of fdm_filament_abs — updated
    2026-05-19 04:14
    Settings (96)
    • activate air filtration added 0
    • additional cooling fan speed added 0
    • chamber temperatures added 0
    • circle compensation speed added 200
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • cool plate temp 80 → 105
    • cool plate temp initial layer 80 → 105
    • cooling perimeter transition distance added 10
    • cooling slowdown logic added uniform_cooling
    • counter coef 1 added 0
    • counter coef 2 added 0.008
    • counter coef 3 added -0.041
    • counter limit max added 0.033
    • counter limit min added -0.035
    • diameter limit added 50
    • during print exhaust fan speed added 70
    • eng plate temp 80 → 105
    • eng plate temp initial layer 80 → 105
    • fan max speed 5 → 80
    • fan min speed 5 → 10
    • filament adaptive volumetric speed added 0
    • filament bridge speed added 25
    • filament change length added 10
    • filament cooling before tower added 0
    • filament density 1.10 → 1.04
    • filament dev ams drying ams limitations added 1
    • filament dev ams drying heat distortion temperature added 45.0
    • filament dev ams drying temperature added 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time added 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature added 90.0
    • filament dev chamber drying time added 12.0
    • filament dev drying cooling temperature added 35.0
    • filament dev drying softening temperature added 40.0
    • filament diameter 2.85 → 1.75
    • filament enable overhang speed added 1
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament extruder compatibility added 0
    • filament extruder variant added Direct Drive Standard
    • filament flush temp added 0
    • filament flush volumetric speed added 0
    • filament long retractions when cut added nil
    • filament long retractions when ec added nil
    • filament max volumetric speed 0 → 28.6
    • filament metal stickiness added None
    • filament overhang 1 4 speed added 0
    • filament overhang 2 4 speed added 50
    • filament overhang 3 4 speed added 30
    • filament overhang 4 4 speed added 10
    • filament overhang totally speed added 10
    • filament pre cooling temperature added 0
    • filament pre cooling temperature nc added 0
    • filament prime volume added 45
    • filament prime volume nc added 60
    • filament printable added 3
    • filament ramming travel time added 0
    • filament ramming travel time nc added 0
    • filament ramming volumetric speed added -1
    • filament ramming volumetric speed nc added -1
    • filament retract length nc added 14
    • filament retraction distances when cut added nil
    • filament retraction distances when ec added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • filament start gcode ; Filament gcode → ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • filament tower interface pre extrusion dist added 10
    • filament tower interface pre extrusion length added 0
    • filament tower interface print temp added -1
    • filament tower interface purge volume added 20
    • filament tower ironing area added 4
    • filament velocity adaptation factor added 1
    • hole coef 1 added 0
    • hole coef 2 added -0.008
    • hole coef 3 added 0.23415
    • hole limit max added 0.22
    • hole limit min added 0.088
    • hot plate temp 80 → 105
    • hot plate temp initial layer 80 → 105
    • impact strength z added 10
    • long retractions when ec added 0
    • no slow down for cooling on outwalls added 0
    • nozzle temperature 235 → 260
    • nozzle temperature initial layer 240 → 260
    • nozzle temperature range high 240 → 270
    • nozzle temperature range low 235 → 240
    • override process overhang speed added 0
    • retraction distances when ec added 0
    • slow down layer time 15 → 3
    • supertack plate temp added 45
    • supertack plate temp initial layer added 45
    • textured plate temp 80 → 60
    • textured plate temp initial layer 80 → 60
    • volumetric speed coefficients added 0 0 0 0 0 0
  25. via parent v1 of Generic ABS @base — created
    2026-05-19 04:02
    Profile created at this point. No prior version to diff against.
  26. via parent v3 of fdm_filament_common — updated
    2026-05-19 04:01
    Settings (81)
    • activate air filtration added 0
    • additional cooling fan speed added 0
    • chamber temperatures added 0
    • circle compensation speed added 200
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • cooling perimeter transition distance added 10
    • cooling slowdown logic added uniform_cooling
    • counter coef 1 added 0
    • counter coef 2 added 0.008
    • counter coef 3 added -0.041
    • counter limit max added 0.033
    • counter limit min added -0.035
    • diameter limit added 50
    • during print exhaust fan speed added 70
    • filament adaptive volumetric speed added 0
    • filament bridge speed added 25
    • filament change length added 10
    • filament cooling before tower added 0
    • filament dev ams drying ams limitations added 1
    • filament dev ams drying heat distortion temperature added 45.0
    • filament dev ams drying temperature added 40.0, 40.0, 40.0, 40.0
    • filament dev ams drying time added 8.0, 8.0, 8.0, 8.0
    • filament dev chamber drying bed temperature added 90.0
    • filament dev chamber drying time added 12.0
    • filament dev drying cooling temperature added 35.0
    • filament dev drying softening temperature added 40.0
    • filament diameter 2.85 → 1.75
    • filament enable overhang speed added 1
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament extruder compatibility added 0
    • filament extruder variant added Direct Drive Standard
    • filament flush temp added 0
    • filament flush volumetric speed added 0
    • filament long retractions when cut added nil
    • filament long retractions when ec added nil
    • filament metal stickiness added None
    • filament overhang 1 4 speed added 0
    • filament overhang 2 4 speed added 50
    • filament overhang 3 4 speed added 30
    • filament overhang 4 4 speed added 10
    • filament overhang totally speed added 10
    • filament pre cooling temperature added 0
    • filament pre cooling temperature nc added 0
    • filament prime volume added 45
    • filament prime volume nc added 60
    • filament printable added 3
    • filament ramming travel time added 0
    • filament ramming travel time nc added 0
    • filament ramming volumetric speed added -1
    • filament ramming volumetric speed nc added -1
    • filament retract length nc added 14
    • filament retraction distances when cut added nil
    • filament retraction distances when ec added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • filament start gcode ; Filament gcode → ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • filament tower interface pre extrusion dist added 10
    • filament tower interface pre extrusion length added 0
    • filament tower interface print temp added -1
    • filament tower interface purge volume added 20
    • filament tower ironing area added 4
    • filament velocity adaptation factor added 1
    • hole coef 1 added 0
    • hole coef 2 added -0.008
    • hole coef 3 added 0.23415
    • hole limit max added 0.22
    • hole limit min added 0.088
    • impact strength z added 10
    • long retractions when ec added 0
    • no slow down for cooling on outwalls added 0
    • nozzle temperature range high added 240
    • nozzle temperature range low added 190
    • override process overhang speed added 0
    • retraction distances when ec added 0
    • supertack plate temp added 45
    • supertack plate temp initial layer added 45
    • volumetric speed coefficients added 0 0 0 0 0 0
  27. via parent v2 of fdm_filament_abs — updated
    2026-05-19 04:01
    Settings (19)
    • bed type removed Cool Plate
    • cool plate temp 105 → 80
    • cool plate temp initial layer 105 → 80
    • eng plate temp 105 → 80
    • eng plate temp initial layer 105 → 80
    • fan max speed 80 → 5
    • fan min speed 10 → 5
    • filament density 1.04 → 1.10
    • filament diameter 1.75 → 2.85
    • filament max volumetric speed 28.6 → 0
    • hot plate temp 105 → 80
    • hot plate temp initial layer 105 → 80
    • nozzle temperature 260 → 235
    • nozzle temperature initial layer 260 → 240
    • nozzle temperature range high 270 → 240
    • nozzle temperature range low 240 → 235
    • slow down layer time 3 → 15
    • textured plate temp 105 → 80
    • textured plate temp initial layer 105 → 80
  28. via parent v2 of fdm_filament_common — updated
    2026-05-19 04:01
    Settings (2)
    • bed type removed Cool Plate
    • filament diameter 1.75 → 2.85
  29. via parent v1 of fdm_filament_abs — created
    2026-05-19 04:01
    Profile created at this point. No prior version to diff against.
  30. via parent v1 of fdm_filament_common — created
    2026-05-19 04:01
    Profile created at this point. No prior version to diff against.