QIDI PETG-Tough

QIDI · PETG · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

*QIDI PETG-Tough*

Inherited from this (24)

View all 24 →

Settings

Basic information

Material variant: PETG overridden
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 overridden
was 0 (inherited)
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 240 overridden
Nozzle (other layers) (°C): 250 overridden

Cooling

Fan minimum (%): 10 overridden
Fan maximum (%): 40 overridden
Disable fan for first N layers: 3 overridden
Full fan if layer below (sec): 30 overridden
Slow down if layer below (sec): 15 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 0.95 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 16 overridden
was 0 (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	80 overridden	80 overridden

Other settings

compatible printers condition: printer_notes=~/.*PRINTER_MODEL_VORON.*/ inherited
cooling: 1 inherited
enable auxiliary fan: 0 overridden
enable dynamic fan speeds: 1 overridden
end filament gcode: ; Filament-specific end gcode inherited
filament colour: #00FF40 overridden
was #FF3232 (inherited)
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
overhang fan speed 0: 100 overridden
overhang fan speed 1: 100 overridden
start filament gcode: ; Filament gcode M900 K0.004 T0.03 overridden
was ; Filament-specific start gcode (inherited)

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_notes": [
    ""
  ],
  "filament_colour": [
    "#00FF40"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "15"
  ],
  "start_filament_gcode": [
    "; Filament gcode\nM900 K0.004 T0.03\n"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_MODEL_VORON.*/"
  ],
  "filament_max_volumetric_speed": [
    "16"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_max_speed": [
    "40"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_type": [
    "PETG"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "enable_auxiliary_fan": [
    "0"
  ],
  "overhang_fan_speed_0": [
    "100"
  ],
  "overhang_fan_speed_1": [
    "100"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "enable_dynamic_fan_speeds": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "name": "*QIDI PETG-Tough*",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:15