Bambu ASA-Aero @base

Bambu Lab · ASA-AERO · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

Bambu ASA-Aero @base

Inherited from this (11)

View all 11 →

Settings

Basic information

Material variant: ASA-AERO overridden
was ASA (inherited)
Vendor: Bambu Lab overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 0.99 overridden
was 1.04 (inherited)
Cost (/kg): 49.99 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 270 overridden
was 240 (inherited)
Nozzle (other layers) (°C): 270 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 30 overridden
was 10 (inherited)
Fan maximum (%): 50 overridden
was 80 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 overridden
was 35 (inherited)
Slow down if layer below (sec): 5 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.52 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 28.6 (inherited)

Retraction

Retraction length (mm): 1.5 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	95 inherited	95 inherited
Engineering Plate	95 inherited	95 inherited
High Temp Plate	95 inherited	95 inherited

Other settings

additional fan full speed layer: 0 inherited
close additional fan first x layers: 3 inherited
description: This filament is only used to print models with a low density usually, and some special parameters are required. To get better printing quality, please refer to this wiki: ASA Aero Printing Guide. overridden
filament dev drying cooling temperature: 70 overridden
filament id: GFB02 overridden
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: 5 overridden
was nil (inherited)
filament z hop: nil inherited
filament z hop types: Normal Lift overridden
full fan speed layer: 0 inherited
impact strength z: 3.4 overridden
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 50 overridden
was 80 (inherited)
overhang fan threshold: 25% inherited
reduce fan stop start freq: 0 overridden
was 1 (inherited)
required nozzle HRC: 3 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "49.99"
  ],
  "filament_type": [
    "ASA-AERO"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "95"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "95"
  ],
  "cool_plate_temp": [
    "95"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "0.99"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "270"
  ],
  "overhang_fan_speed": [
    "50"
  ],
  "filament_flow_ratio": [
    "0.52"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "5"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "1.5"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "95"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "95"
  ],
  "cool_plate_temp_initial_layer": [
    "95"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "270"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "description": "This filament is only used to print models with a low density usually, and some special parameters are required. To get better printing quality, please refer to this wiki: ASA Aero Printing Guide.",
  "filament_id": "GFB02",
  "impact_strength_z": [
    "3.4"
  ],
  "filament_z_hop_types": [
    "Normal Lift"
  ],
  "filament_dev_drying_cooling_temperature": [
    "70"
  ],
  "name": "Bambu ASA-Aero @base"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 04:16
v1 created 2026-05-19 04:01