PLA_VASE_flsunq

Unknown · PLA · by prusa-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common_flsunq*

→

*PLA_flsunq*

→

*PLA_VASE_flsunq*

Inherited from this (1)

Generic PLA VASE @FLSUN

Settings

Basic information

Material variant: PLA inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 205 inherited
Nozzle (other layers) (°C): 200 inherited

Cooling

Fan minimum (%): 35 overridden
was 50 (inherited)
Fan maximum (%): 100 overridden
was 90 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 60 overridden
was 100 (inherited)
Slow down if layer below (sec): 5 overridden
was 15 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 15 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 10 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	60 inherited	60 inherited

Other settings

bridge fan speed: 100 overridden
was 95 (inherited)
compatible printers condition: printer_notes=~/.*PRINTER_VENDOR_FLSun.*/ and printer_notes=~/.*PRINTER_MODEL_Q(QSP|5).*/ inherited
cooling: 1 inherited
end filament gcode: ; Filament-specific end gcode inherited
fan always on: 1 inherited
filament colour: #FF3232 inherited
filament deretract speed: 30 inherited
filament retract length: 3 inherited
filament retract lift: nil inherited
filament retract speed: 30 inherited
filament soluble: 0 inherited
filament wipe: nil inherited
start filament gcode: ; Filament gcode ;M900 K{if nozzle_diameter[0]==0.6}0.12{else}0.22{endif} ; Linear Advance 1.5 inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "fan_min_speed": [
    "35"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    "; Filament-specific end gcode"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "start_filament_gcode": [
    "; Filament gcode\n;M900 K{if nozzle_diameter[0]==0.6}0.12{else}0.22{endif} ; Linear Advance 1.5\n"
  ],
  "compatible_printers_condition": [
    "printer_notes=~/.*PRINTER_VENDOR_FLSun.*/ and printer_notes=~/.*PRINTER_MODEL_Q(QSP|5).*/"
  ],
  "fan_always_on": [
    "1"
  ],
  "fan_max_speed": [
    "100"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "filament_colour": [
    "#FF3232"
  ],
  "bridge_fan_speed": [
    "100"
  ],
  "nozzle_temperature": [
    "200"
  ],
  "filament_retract_lift": [
    "nil"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "filament_retract_speed": [
    "30"
  ],
  "filament_retract_length": [
    "3"
  ],
  "filament_deretract_speed": [
    "30"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "10"
  ],
  "nozzle_temperature_initial_layer": [
    "205"
  ],
  "name": "*PLA_VASE_flsunq*",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:14