Flashforge HS PETG @FF G4P HF

Generic · PETG · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

Flashforge Generic ABS

→

Flashforge Generic ABS @G3U

→

Flashforge HS PETG @FF G4P HF

Compatible printers (1)

Flashforge Guider4 Pro 0.4 HF nozzle

Settings

Basic information

Material variant: PETG overridden
was ABS (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 overridden
was 1.04 (inherited)
Cost (/kg): 30 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 230 overridden
was 235 (inherited)
Nozzle (other layers) (°C): 230 inherited
Chamber (°C): 0 inherited

Cooling

Fan minimum (%): 40 overridden
was 10 (inherited)
Fan maximum (%): 90 overridden
was 30 (inherited)
Disable fan for first N layers: 1 overridden
was 2 (inherited)
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 5 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 30 overridden
was 20 (inherited)

Flow

Flow ratio: 1 overridden
was 1.03 (inherited)
Max volumetric speed (mm³/s): 25 overridden
was 15 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 80	0 overridden was 80
Textured Cool Plate	80 overridden	80 overridden
Engineering Plate	80 inherited	80 inherited
High Temp Plate	80 overridden was 105	80 overridden was 105
Textured PEI Plate	80 inherited	80 inherited

Other settings

activate air filtration: 1 overridden
was 0 (inherited)
activate chamber temp control: 0 inherited
additional cooling fan speed: 40 overridden
was 0 (inherited)
bed type: Cool Plate inherited
compatible printers: Flashforge Guider4 Pro 0.4 HF nozzle overridden
was Flashforge Guider 3 Ultra 0.4 Nozzle, Flashforge Guider 3 Ultra 0.6 Nozzle, Flashforge Guider 3 Ultra 0.8 Nozzle, Flashforge Guider 2s 0.4 nozzle (inherited)
complete print exhaust fan speed: 40 overridden
was 80 (inherited)
during print exhaust fan speed: 40 overridden
was 60 (inherited)
enable overhang bridge fan: 1 inherited
enable pressure advance: 1 inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament id: GFB99 inherited
filament is support: 0 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 overridden
was 5 (inherited)
filament multitool ramming: 0 inherited
filament multitool ramming flow: 10 inherited
filament multitool ramming volume: 10 inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before wipe: nil inherited
filament retract lift above: nil inherited
filament retract lift below: nil inherited
filament retract lift enforce: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 overridden
was 35 (inherited)
filament unloading speed start: 100 overridden
was 40 (inherited)
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 260 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 80 overridden
was 50 (inherited)
overhang fan threshold: 25% inherited
pressure advance: 0.075 overridden
was 0.036 (inherited)
reduce fan stop start freq: 1 inherited
required nozzle HRC: 0 inherited
setting id: GFSA04 inherited
slow down for layer cooling: 1 inherited
support material interface fan speed: 90 overridden
was 40 (inherited)
temperature vitrification: 70 overridden
was 100 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "90"
  ],
  "fan_min_speed": [
    "40"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "80"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "230"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "30"
  ],
  "textured_plate_temp": [
    "80"
  ],
  "filament_settings_id": [
    "Flashforge HS PETG @FF G4P HF"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n;right_extruder_material: PLA\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "80"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "25"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "230"
  ],
  "textured_plate_temp_initial_layer": [
    "80"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "40"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "pressure_advance": [
    "0.075"
  ],
  "compatible_printers": [
    "Flashforge Guider4 Pro 0.4 HF nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "support_material_interface_fan_speed": [
    "90"
  ],
  "filament_notes": [
    ""
  ],
  "filament_shrink": [
    "100%"
  ],
  "compatible_prints": [],
  "filament_load_time": [
    "0"
  ],
  "chamber_temperature": [
    "0"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "filament_unload_time": [
    "0"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "default_filament_colour": [
    ""
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "compatible_prints_condition": "",
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "compatible_printers_condition": "",
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "during_print_exhaust_fan_speed": [
    "40"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "complete_print_exhaust_fan_speed": [
    "40"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "textured_cool_plate_temp": [
    "80"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "80"
  ],
  "name": "Flashforge HS PETG @FF G4P HF"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:14