COEX PLA+Silk @System

COEX 3D · PLA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

fdm_filament_pla_silk

→

COEX PLA+Silk @base

→

COEX PLA+Silk @System

Settings

Basic information

Material variant: PLA inherited
Vendor: COEX 3D inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 30.00 inherited

Print temperature

Nozzle (initial layer) (°C): 245 inherited
Nozzle (other layers) (°C): 240 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.98 inherited
Max volumetric speed (mm³/s): 15 overridden
was 15 (inherited)

Retraction

Retraction length (mm): 1.5 inherited
Retraction speed (mm/s): 45 inherited
Deretraction speed (mm/s): 40 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 0 inherited
bed temperature: 60 inherited
bed temperature initial layer: 60 inherited
bed type: Cool Plate inherited
description: To make the prints get higher gloss, please dry the filament before use, and set the outer wall speed to be 40 to 60 mm/s when slicing. inherited
disable fan first layers: 1 inherited
external perimeter speed: 50% inherited
filament id: CXPLSB03 inherited
filament long retractions when cut: nil overridden
filament minimal purge on wipe tower: 15 inherited
filament notes: Silk finish for aesthetic prints - slightly higher temperature than regular PLA inherited
filament retract before wipe: 70% inherited
filament retract layer change: 1 inherited
filament retract restart extra: nil inherited
filament retract when changing layer: 1 inherited
filament retraction distances when cut: nil overridden
filament retraction minimum travel: 2 inherited
filament soluble: 0 inherited
filament wipe: 1 inherited
filament wipe distance: 2 inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 3 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: C0XPLS03 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 55 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "30.00"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "1"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "COEX 3D"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "2"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "45"
  ],
  "temperature_vitrification": [
    "55"
  ],
  "filament_retraction_length": [
    "1.5"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "40"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "70%"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "2"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "description": "To make the prints get higher gloss, please dry the filament before use, and set the outer wall speed to be 40 to 60 mm/s when slicing.",
  "filament_id": "CXPLSB03",
  "filament_notes": "Silk finish for aesthetic prints - slightly higher temperature than regular PLA",
  "bed_temperature": [
    "60"
  ],
  "compatible_prints": [],
  "compatible_printers": [],
  "disable_fan_first_layers": [
    "1"
  ],
  "external_perimeter_speed": [
    "50%"
  ],
  "compatible_prints_condition": "",
  "bed_temperature_initial_layer": [
    "60"
  ],
  "compatible_printers_condition": "",
  "filament_retract_layer_change": [
    "1"
  ],
  "setting_id": "C0XPLS03",
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "name": "COEX PLA+Silk @System"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:14