Artillery PETG Basic @Artillery M1 Pro 0.4 nozzle

Artillery · PETG BASIC · 0.40mm nozzle · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Artillery Generic PLA

→

Artillery PETG Basic @Artillery M1 Pro 0.4 nozzle

Compatible printers (1)

Artillery M1 Pro 0.4 nozzle

Settings

Basic information

Material variant: PETG Basic overridden
was PLA (inherited)
Vendor: Artillery overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 overridden
was 1.24 (inherited)
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 200 (inherited)
Nozzle (other layers) (°C): 250 overridden
was 200 (inherited)

Cooling

Fan minimum (%): 40 overridden
was 100 (inherited)
Fan maximum (%): 90 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 30 overridden
was 100 (inherited)
Slow down if layer below (sec): 12 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 5 (inherited)

Flow

Flow ratio: 0.95 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 12 (inherited)

Retraction

Retraction length (mm): 0.8 overridden
was nil (inherited)
Retraction speed (mm/s): 30 overridden
was nil (inherited)
Deretraction speed (mm/s): 30 overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	70 overridden was 50	70 overridden was 50
Engineering Plate	50 inherited	50 inherited
High Temp Plate	70 overridden was 60	70 overridden was 60
Textured PEI Plate	70 overridden was 50	70 overridden was 50

Other settings

additional cooling fan speed: 0 overridden
was 0 (inherited)
bed type: Cool Plate inherited
compatible printers: Artillery M1 Pro 0.4 nozzle overridden
was Artillery Sidewinder X1 0.4 nozzle, Artillery Genius 0.4 nozzle, Artillery Sidewinder X2 0.4 nozzle, Artillery Genius Pro 0.4 nozzle, Artillery Hornet 0.4 nozzle (inherited)
complete print exhaust fan speed: 0 overridden
during print exhaust fan speed: 60 overridden
enable pressure advance: 1 overridden
filament id: GFL99 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: 0% overridden
was nil (inherited)
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.4 overridden
was nil (inherited)
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 270 overridden
was 230 (inherited)
nozzle temperature range low: 220 overridden
was 190 (inherited)
overhang fan speed: 100 overridden
was 100 (inherited)
overhang fan threshold: 10% overridden
was 50% (inherited)
pressure advance: 0.063 overridden
reduce fan stop start freq: 1 inherited
setting id: GFSA04 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 70 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "90"
  ],
  "fan_min_speed": [
    "40"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG Basic"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "0.4"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "70"
  ],
  "filament_vendor": [
    "Artillery"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "filament_settings_id": [
    "Artillery PETG Basic @Artillery M1 Pro 0.4 nozzle"
  ],
  "filament_start_gcode": [
    "; filament start gcode "
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "30"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "0.8"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "30"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "0%"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "70"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFL99",
  "compatible_printers": [
    "Artillery M1 Pro 0.4 nozzle"
  ],
  "pressure_advance": [
    "0.063"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "during_print_exhaust_fan_speed": [
    "60"
  ],
  "complete_print_exhaust_fan_speed": [
    "0"
  ],
  "name": "Artillery PETG Basic @Artillery M1 Pro 0.4 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:13