Prusa Generic PLA @MK4S HF0.8

Generic · PLA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Prusa Generic PLA @MK4S

→

Prusa Generic PLA @MK4S HF0.4

→

Prusa Generic PLA @MK4S HF0.8

Compatible printers (1)

Prusa MK4S HF0.8 nozzle

Settings

Basic information

Material variant: PLA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 25.4 inherited

Print temperature

Nozzle (initial layer) (°C): 230 inherited
Nozzle (other layers) (°C): 225 inherited

Cooling

Fan minimum (%): 80 overridden
was 70 (inherited)
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 25 overridden
was 17 (inherited)
Slow down if layer below (sec): 15 overridden
was 6 (inherited)
Min speed when slowed (mm/s): 15 overridden
was 20 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 35 overridden
was 22 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Custom G-code

filament_start_gcode inherited

M572 S{if nozzle_diameter[0]==0.4}0.036{elsif nozzle_diameter[0]==0.5}0.026{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.015{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.08{else}0{endif} ; Filament gcode

M142 S36 ; set heatbreak target temp

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Prusa MK4S HF0.8 nozzle overridden
was Prusa MK4S HF0.4 nozzle (inherited)
default filament colour: #FF8000 inherited
filament id: Generic PLA @MK4S HF0.8 overridden
was Generic PLA @MK4S HF0.4 (inherited)
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 250 100 40 40| 0.05 40 0.45 40 0.95 40 1.45 40 1.95 40 2.45 40 2.95 40 3.45 40 3.95 40 4.45 40 4.95 40 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 3 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": "80",
  "filament_cost": [
    "25.4"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode"
  ],
  "nozzle_temperature": "225",
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": "15",
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "M572 S{if nozzle_diameter[0]==0.4}0.036{elsif nozzle_diameter[0]==0.5}0.026{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.015{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.08{else}0{endif} ; Filament gcode\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": "3",
  "slow_down_layer_time": "15",
  "fan_cooling_layer_time": "25",
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "35"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": "230",
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "setting_id": "GFSA04",
  "filament_id": "Generic PLA @MK4S HF0.8",
  "filament_notes": [
    ""
  ],
  "compatible_printers": [
    "Prusa MK4S HF0.8 nozzle"
  ],
  "default_filament_colour": "#FF8000",
  "filament_ramming_parameters": [
    "250 100 40 40| 0.05 40 0.45 40 0.95 40 1.45 40 1.95 40 2.45 40 2.95 40 3.45 40 3.95 40 4.45 40 4.95 40"
  ],
  "name": "Prusa Generic PLA @MK4S HF0.8"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:12