Flashforge PLA-CF @FF G4P

Generic · PLA-CF · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Flashforge Generic HS PLA

→

Flashforge PLA-CF @FF G4P

Compatible printers (1)

Flashforge Guider4 Pro 0.4 nozzle

Settings

Basic information

Material variant: PLA-CF overridden
was PLA (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 215 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 215 overridden
was 220 (inherited)
Chamber (°C): 0 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 8 overridden
was 6 (inherited)
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.98 inherited
Max volumetric speed (mm³/s): 20 overridden
was 25 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	55 overridden was 60	55 overridden was 60
Engineering Plate	55 overridden was 60	55 overridden was 60
High Temp Plate	55 inherited	55 overridden was 50
Textured PEI Plate	55 overridden was 60	55 overridden was 60

Other settings

additional cooling fan speed: 40 overridden
was 100 (inherited)
bed temperature difference: 10 inherited
bed type: Cool Plate inherited
compatible printers: Flashforge Guider4 Pro 0.4 nozzle overridden
was Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle, Flashforge AD5X 0.4 nozzle, Flashforge AD5X 0.6 nozzle, Flashforge AD5X 0.8 nozzle (inherited)
complete print exhaust fan speed: 40 overridden
during print exhaust fan speed: 40 overridden
enable overhang bridge fan: 1 inherited
enable pressure advance: 1 inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament id: GFL99 inherited
filament is support: 0 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament multitool ramming: 0 inherited
filament multitool ramming flow: 10 inherited
filament multitool ramming volume: 10 inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before wipe: nil inherited
filament retract lift above: nil inherited
filament retract lift below: nil inherited
filament retract lift enforce: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 240 overridden
was 230 (inherited)
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
pressure advance: 0.045 overridden
was 0.025 (inherited)
reduce fan stop start freq: 1 inherited
required nozzle HRC: 0 inherited
setting id: GFSA04 inherited
slow down for layer cooling: 1 inherited
support material interface fan speed: 100 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PLA-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "55"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "55"
  ],
  "cool_plate_temp": [
    "55"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "215"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "55"
  ],
  "filament_settings_id": [
    "Flashforge PLA-CF @FF G4P"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n;right_extruder_material:PLA-CF\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "55"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "55"
  ],
  "cool_plate_temp_initial_layer": [
    "55"
  ],
  "filament_max_volumetric_speed": [
    "20"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "215"
  ],
  "textured_plate_temp_initial_layer": [
    "55"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "40"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "240"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFL99",
  "filament_notes": [
    ""
  ],
  "filament_shrink": [
    "100%"
  ],
  "pressure_advance": [
    "0.045"
  ],
  "compatible_prints": [],
  "filament_load_time": [
    "0"
  ],
  "chamber_temperature": [
    "0"
  ],
  "compatible_printers": [
    "Flashforge Guider4 Pro 0.4 nozzle"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "filament_unload_time": [
    "0"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "bed_temperature_difference": [
    "10"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "compatible_prints_condition": "",
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": "",
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "support_material_interface_fan_speed": [
    "100"
  ],
  "during_print_exhaust_fan_speed": [
    "40"
  ],
  "complete_print_exhaust_fan_speed": [
    "40"
  ],
  "name": "Flashforge PLA-CF @FF G4P"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:11