Polymaker PETG @Snapmaker U1

Polymaker · PETG · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_petg

→

Polymaker PETG @Base

→

Polymaker PETG @Snapmaker U1

Compatible printers (1)

Snapmaker U1 (0.4 nozzle)

Settings

Basic information

Material variant: PETG inherited
Vendor: Polymaker overridden
was Polymaker (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.3 inherited
Cost (/kg): 0 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 260 overridden
was 245 (inherited)
Nozzle (other layers) (°C): 260 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 50 overridden
was 20 (inherited)
Fan maximum (%): 10 overridden
was 80 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 6 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 30 (inherited)

Flow

Flow ratio: 0.96 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 15 overridden
was 20 (inherited)

Retraction

Retraction length (mm): 1.0 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 overridden was 70	60 overridden was 70
Engineering Plate	0 overridden was 70	0 overridden was 70
High Temp Plate	80 overridden was 70	80 overridden was 70
Textured PEI Plate	80 overridden was 70	80 overridden was 70
Cool Plate SuperTack	70 overridden	70 overridden

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate overridden
was Cool Plate (inherited)
compatible printers: Snapmaker U1 (0.4 nozzle) overridden
filament id: PMPE01 overridden
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.0 inherited
filament z hop types: nil inherited
full fan speed layer: 0 overridden
was 0 (inherited)
idle temperture: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 260 overridden
was 255 (inherited)
nozzle temperature range low: 240 overridden
was 210 (inherited)
overhang fan speed: 100 overridden
was 70 (inherited)
overhang fan threshold: 95% overridden
was 25% (inherited)
reduce fan stop start freq: 1 inherited
setting id: PMPE01_U1 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
temp max: 260 inherited
temp min: 240 inherited
temperature vitrification: 71 overridden
was 70 (inherited)
temperture vitrification: 75 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "10"
  ],
  "fan_min_speed": [
    "50"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "0.0"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Polymaker"
  ],
  "filament_density": [
    "1.3"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.96"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "80"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "6"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "71"
  ],
  "filament_retraction_length": [
    "1.0"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "80"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "temp_max": [
    "260"
  ],
  "temp_min": [
    "240"
  ],
  "description": "",
  "idle_temperture": [
    "0"
  ],
  "temperture_vitrification": [
    "75"
  ],
  "setting_id": "PMPE01_U1",
  "filament_id": "PMPE01",
  "compatible_printers": [
    "Snapmaker U1 (0.4 nozzle)"
  ],
  "supertack_plate_temp": [
    "70"
  ],
  "supertack_plate_temp_initial_layer": [
    "70"
  ],
  "name": "Polymaker PETG @Snapmaker U1"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:09