Snapmaker ABS Benchy @U1

Generic · ABS · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

Snapmaker ABS @U1 base

→

Snapmaker ABS Benchy @U1

Compatible printers (1)

Snapmaker U1 (0.4 nozzle)

Settings

Basic information

Material variant: ABS inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 250 inherited
Nozzle (other layers) (°C): 250 overridden
was 250 (inherited)

Cooling

Fan minimum (%): 35 overridden
was 18 (inherited)
Fan maximum (%): 50 overridden
was 15 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 2 overridden
was 5 (inherited)
Slow down if layer below (sec): 0 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 0 overridden
was 30 (inherited)

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 31 overridden
was 8 (inherited)

Retraction

Retraction length (mm): 0.5 overridden
was nil (inherited)
Retraction speed (mm/s): 55 overridden
was nil (inherited)
Deretraction speed (mm/s): 55 overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	105 inherited	110 inherited
Textured PEI Plate	105 inherited	105 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Snapmaker U1 (0.4 nozzle) overridden
compatible prints: 0.25 Benchy @Snapmaker U1 (0.4 nozzle) overridden
filament cooling final speed: 60 inherited
filament cooling initial speed: 35 inherited
filament cooling moves: 2 inherited
filament id: 1682237920 inherited
filament load time: 2 inherited
filament loading speed: 35 inherited
filament loading speed start: 35 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: 0 overridden
was nil (inherited)
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament unload time: 2 inherited
filament unloading speed: 35 inherited
filament unloading speed start: 35 inherited
filament wipe: 0 overridden
was nil (inherited)
filament wipe distance: nil inherited
filament z hop: 0 overridden
was nil (inherited)
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 35 overridden
was 20 (inherited)
overhang fan threshold: 25% inherited
pressure advance: 0.02 inherited
reduce fan stop start freq: 1 inherited
setting id: 35407544770 overridden
slow down for layer cooling: 0 overridden
was 1 (inherited)
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "35"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "0"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "0"
  ],
  "hot_plate_temp": [
    "110"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    ""
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "35"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "0"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "0"
  ],
  "fan_cooling_layer_time": [
    "2"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "55"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "0.5"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "55"
  ],
  "slow_down_for_layer_cooling": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "31"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "0"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "filament_id": "1682237920",
  "pressure_advance": [
    "0.02"
  ],
  "filament_load_time": [
    "2"
  ],
  "filament_unload_time": [
    "2"
  ],
  "filament_cooling_moves": [
    "2"
  ],
  "filament_loading_speed": [
    "35"
  ],
  "filament_unloading_speed": [
    "35"
  ],
  "filament_cooling_final_speed": [
    "60"
  ],
  "filament_loading_speed_start": [
    "35"
  ],
  "filament_cooling_initial_speed": [
    "35"
  ],
  "filament_unloading_speed_start": [
    "35"
  ],
  "setting_id": "35407544770",
  "compatible_prints": [
    "0.25 Benchy @Snapmaker U1 (0.4 nozzle)"
  ],
  "compatible_printers": [
    "Snapmaker U1 (0.4 nozzle)"
  ],
  "default_filament_colour": [
    ""
  ],
  "name": "Snapmaker ABS Benchy @U1"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:09