PolyTerra PLA @BBL X1C

Polymaker · PLA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

PolyTerra PLA @base

→

PolyTerra PLA @BBL X1C

Compatible printers (9)

Bambu Lab P1S 0.4 nozzle
Bambu Lab P1S 0.6 nozzle
Bambu Lab P1S 0.8 nozzle
Bambu Lab X1 Carbon 0.4 nozzle
Bambu Lab X1 Carbon 0.6 nozzle
Bambu Lab X1 Carbon 0.8 nozzle
Bambu Lab X1E 0.4 nozzle
Bambu Lab X1E 0.6 nozzle
Bambu Lab X1E 0.8 nozzle

Inherited from this (2)

Settings

Basic information

Material variant: PLA inherited
Vendor: Polymaker inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.31 inherited
Cost (/kg): 25.4 inherited

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 5 inherited

Flow

Flow ratio: 0.98 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 22 overridden
was 20 (inherited)

Retraction

Retraction length (mm): nil overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Custom G-code

filament_start_gcode overridden

; filament start gcode
{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200
{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150
{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50
{endif}

{if activate_air_filtration[current_extruder] && support_air_filtration}
M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} 
{endif}

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Bambu Lab X1 Carbon 0.4 nozzle, Bambu Lab X1 Carbon 0.6 nozzle, Bambu Lab X1 Carbon 0.8 nozzle, Bambu Lab P1S 0.4 nozzle, Bambu Lab P1S 0.6 nozzle, Bambu Lab P1S 0.8 nozzle, Bambu Lab X1E 0.4 nozzle, Bambu Lab X1E 0.6 nozzle, Bambu Lab X1E 0.8 nozzle overridden
filament adaptive volumetric speed: 0, 0 overridden
filament extruder variant: Direct Drive Standard, Direct Drive High Flow overridden
filament flush temp: 0, 0 overridden
filament flush volumetric speed: 0, 0 overridden
filament id: GFL01 inherited
filament long retractions when cut: nil, nil overridden
filament minimal purge on wipe tower: 15 inherited
filament pre cooling temperature: 0, 0 overridden
filament ramming travel time: 0, 0 overridden
filament ramming volumetric speed: -1, -1 overridden
filament retract before wipe: nil, nil overridden
was nil (inherited)
filament retract restart extra: nil, nil overridden
was nil (inherited)
filament retract when changing layer: nil, nil overridden
was nil (inherited)
filament retraction distances when cut: nil, nil overridden
filament retraction minimum travel: nil, nil overridden
was nil (inherited)
filament soluble: 0 inherited
filament wipe: nil, nil overridden
was nil (inherited)
filament wipe distance: nil, nil overridden
was nil (inherited)
filament z hop: nil, nil overridden
was nil (inherited)
filament z hop types: nil, nil overridden
was nil (inherited)
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
long retractions when ec: 0, 0 overridden
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
retraction distances when ec: 0, 0 overridden
setting id: GFSL18 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited
volumetric speed coefficients: 0 0 0 0 0 0, 0 0 0 0 0 0 overridden

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "25.4"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil",
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Polymaker"
  ],
  "filament_density": [
    "1.31"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220",
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.98",
    "0.98"
  ],
  "slow_down_min_speed": [
    "5"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
  ],
  "filament_z_hop_types": [
    "nil",
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil",
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil",
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "22",
    "22"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220",
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "filament_id": "GFL01",
  "setting_id": "GFSL18",
  "compatible_printers": [
    "Bambu Lab X1 Carbon 0.4 nozzle",
    "Bambu Lab X1 Carbon 0.6 nozzle",
    "Bambu Lab X1 Carbon 0.8 nozzle",
    "Bambu Lab P1S 0.4 nozzle",
    "Bambu Lab P1S 0.6 nozzle",
    "Bambu Lab P1S 0.8 nozzle",
    "Bambu Lab X1E 0.4 nozzle",
    "Bambu Lab X1E 0.6 nozzle",
    "Bambu Lab X1E 0.8 nozzle"
  ],
  "filament_flush_temp": [
    "0",
    "0"
  ],
  "long_retractions_when_ec": [
    "0",
    "0"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow"
  ],
  "filament_ramming_travel_time": [
    "0",
    "0"
  ],
  "retraction_distances_when_ec": [
    "0",
    "0"
  ],
  "volumetric_speed_coefficients": [
    "0 0 0 0 0 0",
    "0 0 0 0 0 0"
  ],
  "filament_flush_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed": [
    "-1",
    "-1"
  ],
  "filament_adaptive_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "nil",
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil",
    "nil"
  ],
  "name": "PolyTerra PLA @BBL X1C"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:08