COEX PETG @BBL A1M 0.2 nozzle

COEX 3D · PETG · 0.20mm nozzle · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

COEX PETG @base

→

COEX PETG @BBL X1C 0.2 nozzle

→

COEX PETG @BBL A1M 0.2 nozzle

Compatible printers (1)

Bambu Lab A1 mini 0.2 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: COEX 3D inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 33.00 inherited

Print temperature

Nozzle (initial layer) (°C): 250 inherited
Nozzle (other layers) (°C): 245 inherited

Cooling

Fan minimum (%): 30 inherited
Fan maximum (%): 50 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 5 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.94 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 6 inherited

Retraction

Retraction length (mm): 4 inherited
Retraction speed (mm/s): 30 inherited
Deretraction speed (mm/s): 30 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	70 inherited	0 inherited
High Temp Plate	70 inherited	80 inherited
Textured PEI Plate	70 inherited	80 inherited

Other settings

bed temperature: 80 inherited
bed temperature initial layer: 85 inherited
bed type: Cool Plate inherited
compatible printers: Bambu Lab A1 mini 0.2 nozzle overridden
was Bambu Lab X1 Carbon 0.2 nozzle, Bambu Lab X1 0.2 nozzle, Bambu Lab P1P 0.2 nozzle, Bambu Lab P1S 0.2 nozzle, Bambu Lab X1E 0.2 nozzle (inherited)
disable fan first layers: 2 inherited
enable pressure advance: 1 inherited
filament id: CXPETB13 inherited
filament long retractions when cut: nil overridden
was 1 (inherited)
filament minimal purge on wipe tower: 15 inherited
filament notes: IMPORTANT: Set travel speed to maximum your machine allows (200-500mm/s) to reduce stringing inherited
filament retract before wipe: 70% inherited
filament retract layer change: 1 inherited
filament retract restart extra: nil inherited
filament retract when changing layer: 1 inherited
filament retraction distances when cut: nil overridden
was 18 (inherited)
filament retraction minimum travel: 2 inherited
filament soluble: 0 inherited
filament wipe: 1 inherited
filament wipe distance: 2 inherited
filament z hop: 0.4 inherited
filament z hop types: nil inherited
full fan speed layer: 4 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 70 inherited
overhang fan threshold: 95% inherited
pressure advance: 0.045 inherited
reduce fan stop start freq: 1 inherited
setting id: CXPETX06 overridden
was CXPETX03 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 70 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "33.00"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "1"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "0.4"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "COEX 3D"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "245"
  ],
  "overhang_fan_speed": [
    "70"
  ],
  "filament_flow_ratio": [
    "0.94"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "80"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "4"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "5"
  ],
  "filament_wipe_distance": [
    "2"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "30"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "30"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "70%"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "6"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "2"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "1"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "filament_id": "CXPETB13",
  "filament_notes": "IMPORTANT: Set travel speed to maximum your machine allows (200-500mm/s) to reduce stringing",
  "bed_temperature": [
    "80"
  ],
  "pressure_advance": [
    "0.045"
  ],
  "compatible_prints": [],
  "compatible_printers": [
    "Bambu Lab A1 mini 0.2 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "disable_fan_first_layers": [
    "2"
  ],
  "compatible_prints_condition": "",
  "bed_temperature_initial_layer": [
    "85"
  ],
  "compatible_printers_condition": "",
  "filament_retract_layer_change": [
    "1"
  ],
  "setting_id": "CXPETX06",
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "name": "COEX PETG @BBL A1M 0.2 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:07