COEX PLA @BBL X1C 0.2 nozzle

COEX 3D · PLA · 0.20mm nozzle · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

→

→

→

→

COEX PLA @BBL X1C 0.2 nozzle

Compatible printers (4)

Bambu Lab P1S 0.2 nozzle
Bambu Lab X1 0.2 nozzle
Bambu Lab X1 Carbon 0.2 nozzle
Bambu Lab X1E 0.2 nozzle

Settings

Basic information

Material variant: PLA inherited
Vendor: COEX 3D inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 24.00 inherited

Print temperature

Nozzle (initial layer) (°C): 235 inherited
Nozzle (other layers) (°C): 230 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 1.6 overridden
was 18 (inherited)

Retraction

Retraction length (mm): 1.5 inherited
Retraction speed (mm/s): 45 inherited
Deretraction speed (mm/s): 40 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 0 inherited
bed temperature: 60 inherited
bed temperature initial layer: 60 inherited
bed type: Cool Plate inherited
compatible printers: Bambu Lab X1 Carbon 0.2 nozzle, Bambu Lab X1 0.2 nozzle, Bambu Lab P1S 0.2 nozzle, Bambu Lab X1E 0.2 nozzle overridden
was Bambu Lab X1 Carbon 0.4 nozzle, Bambu Lab X1 Carbon 0.6 nozzle, Bambu Lab X1 Carbon 0.8 nozzle, Bambu Lab P1S 0.4 nozzle, Bambu Lab P1S 0.6 nozzle, Bambu Lab P1S 0.8 nozzle, Bambu Lab X1E 0.4 nozzle, Bambu Lab X1E 0.6 nozzle, Bambu Lab X1E 0.8 nozzle (inherited)
disable fan first layers: 1 inherited
filament id: CXPLAB02 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: 70% inherited
filament retract layer change: 1 inherited
filament retract restart extra: nil inherited
filament retract when changing layer: 1 inherited
filament retraction minimum travel: 2 inherited
filament soluble: 0 inherited
filament wipe: 1 inherited
filament wipe distance: 2 inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 3 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: CXPLAX02 overridden
was CXPLAX01 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 55 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "24.00"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "1"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "COEX 3D"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "230"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "2"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "45"
  ],
  "temperature_vitrification": [
    "55"
  ],
  "filament_retraction_length": [
    "1.5"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "40"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "70%"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "1.6"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "235"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "2"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "filament_id": "CXPLAB02",
  "bed_temperature": [
    "60"
  ],
  "compatible_prints": [],
  "compatible_printers": [
    "Bambu Lab X1 Carbon 0.2 nozzle",
    "Bambu Lab X1 0.2 nozzle",
    "Bambu Lab P1S 0.2 nozzle",
    "Bambu Lab X1E 0.2 nozzle"
  ],
  "disable_fan_first_layers": [
    "1"
  ],
  "compatible_prints_condition": "",
  "bed_temperature_initial_layer": [
    "60"
  ],
  "compatible_printers_condition": "",
  "filament_retract_layer_change": [
    "1"
  ],
  "setting_id": "CXPLAX02",
  "name": "COEX PLA @BBL X1C 0.2 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:06