COEX PETG @BBL A1 0.2 nozzle

COEX 3D · PETG · 0.20mm nozzle · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

COEX PETG @base

→

COEX PETG @BBL A1 0.2 nozzle

Compatible printers (1)

Bambu Lab A1 0.2 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: COEX 3D inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 33.00 inherited

Print temperature

Nozzle (initial layer) (°C): 250 inherited
Nozzle (other layers) (°C): 245 inherited

Cooling

Fan minimum (%): 30 inherited
Fan maximum (%): 50 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 5 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.94 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 6 overridden
was 12 (inherited)

Retraction

Retraction length (mm): 4 inherited
Retraction speed (mm/s): 30 inherited
Deretraction speed (mm/s): 30 inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	70 inherited	0 inherited
High Temp Plate	70 inherited	80 inherited
Textured PEI Plate	70 inherited	80 inherited

Other settings

bed temperature: 80 inherited
bed temperature initial layer: 85 inherited
bed type: Cool Plate inherited
compatible printers: Bambu Lab A1 0.2 nozzle overridden
was — (inherited)
disable fan first layers: 2 inherited
enable pressure advance: 1 inherited
filament id: CXPETB13 inherited
filament minimal purge on wipe tower: 15 inherited
filament notes: IMPORTANT: Set travel speed to maximum your machine allows (200-500mm/s) to reduce stringing inherited
filament retract before wipe: 70% inherited
filament retract layer change: 1 inherited
filament retract restart extra: nil inherited
filament retract when changing layer: 1 inherited
filament retraction minimum travel: 2 inherited
filament soluble: 0 inherited
filament wipe: 1 inherited
filament wipe distance: 2 inherited
filament z hop: 0.4 inherited
filament z hop types: nil inherited
full fan speed layer: 4 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 70 inherited
overhang fan threshold: 95% inherited
pressure advance: 0.045 inherited
reduce fan stop start freq: 1 inherited
setting id: CXPETX09 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 70 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "33.00"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "1"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "0.4"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "COEX 3D"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "245"
  ],
  "overhang_fan_speed": [
    "70"
  ],
  "filament_flow_ratio": [
    "0.94"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "80"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "4"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "5"
  ],
  "filament_wipe_distance": [
    "2"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "30"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "4"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "30"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "70%"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "6"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "2"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "1"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "filament_id": "CXPETB13",
  "filament_notes": "IMPORTANT: Set travel speed to maximum your machine allows (200-500mm/s) to reduce stringing",
  "bed_temperature": [
    "80"
  ],
  "pressure_advance": [
    "0.045"
  ],
  "compatible_prints": [],
  "compatible_printers": [
    "Bambu Lab A1 0.2 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "disable_fan_first_layers": [
    "2"
  ],
  "compatible_prints_condition": "",
  "bed_temperature_initial_layer": [
    "85"
  ],
  "compatible_printers_condition": "",
  "filament_retract_layer_change": [
    "1"
  ],
  "setting_id": "CXPETX09",
  "name": "COEX PETG @BBL A1 0.2 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:06