Bambu Support For PLA/PETG @base

Bambu Lab · PLA · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Bambu Support For PLA/PETG @base

Inherited from this (22)

View all 22 →

Settings

Basic information

Material variant: PLA inherited
Vendor: Bambu Lab overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.19 overridden
was 1.24 (inherited)
Cost (/kg): 69.98 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 210 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 210 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 20 overridden
was 100 (inherited)
Fan maximum (%): 30 overridden
was 100 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 80 overridden
was 100 (inherited)
Slow down if layer below (sec): 8 overridden
was 4 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 6 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	35 inherited	35 inherited
Engineering Plate	0 inherited	0 inherited
High Temp Plate	60 overridden was 60	60 overridden was 60
Textured PEI Plate	60 overridden	60 overridden
Cool Plate SuperTack	0 overridden	—

Other settings

additional cooling fan speed: 70 inherited
additional fan full speed layer: 0 inherited
close additional fan first x layers: 1 inherited
description: This is a non-water-soluble support filament, and usually it is only for the support structure and not for the model body. To get better printing quality, please refer to this wiki: Printing Tips for Support Filament and Support Function. overridden
enable overhang bridge fan: 0 inherited
filament adhesiveness category: 705 overridden
filament dev ams drying heat distortion temperature: 50 overridden
filament dev ams drying temperature: 60, 60, 50, 50 overridden
filament dev chamber drying bed temperature: 80 overridden
filament dev drying softening temperature: 55 overridden
filament id: GFS05 overridden
filament is support: 1 overridden
was 0 (inherited)
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
slow down for layer cooling: 0 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "69.98"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "cool_plate_temp": [
    "35"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "1.19"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "210"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_is_support": [
    "1"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "80"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "cool_plate_temp_initial_layer": [
    "35"
  ],
  "filament_max_volumetric_speed": [
    "6"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "210"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "1"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "enable_overhang_bridge_fan": [
    "0"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "description": "This is a non-water-soluble support filament, and usually it is only for the support structure and not for the model body. To get better printing quality, please refer to this wiki: Printing Tips for Support Filament and Support Function.",
  "filament_id": "GFS05",
  "textured_plate_temp": [
    "60"
  ],
  "filament_adhesiveness_category": [
    "705"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "filament_dev_ams_drying_temperature": [
    "60",
    "60",
    "50",
    "50"
  ],
  "filament_dev_drying_softening_temperature": [
    "55"
  ],
  "filament_dev_chamber_drying_bed_temperature": [
    "80"
  ],
  "filament_dev_ams_drying_heat_distortion_temperature": [
    "50"
  ],
  "name": "Bambu Support For PLA/PETG @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:15