Generic HIPS @BBL H2DP 0.2 nozzle

Generic · HIPS · 0.20mm nozzle · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_hips

→

Generic HIPS @base

→

Generic HIPS @BBL H2DP 0.2 nozzle

Compatible printers (1)

Bambu Lab H2D Pro 0.2 nozzle

Settings

Basic information

Material variant: HIPS inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.06 inherited
Cost (/kg): 22.99 inherited

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 240 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 0 inherited
Fan maximum (%): 60 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 10 inherited
Slow down if layer below (sec): 6 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 0.5 overridden
was 8 (inherited)

Retraction

Retraction length (mm): nil overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	90 inherited	90 inherited
High Temp Plate	90 inherited	90 inherited
Textured PEI Plate	90 inherited	90 inherited
Cool Plate SuperTack	0 inherited	0 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Bambu Lab H2D Pro 0.2 nozzle overridden
filament adaptive volumetric speed: 0, 0 overridden
filament extruder variant: Direct Drive Standard, Direct Drive High Flow overridden
filament flush temp: 0, 0 overridden
filament flush volumetric speed: 0, 0 overridden
filament id: GFS98 inherited
filament is support: 1 inherited
filament long retractions when cut: nil, nil overridden
filament minimal purge on wipe tower: 15 inherited
filament pre cooling temperature: 0, 0 overridden
filament ramming travel time: 0, 0 overridden
filament ramming volumetric speed: -1, -1 overridden
filament retract before wipe: nil, nil overridden
was nil (inherited)
filament retract restart extra: nil, nil overridden
was nil (inherited)
filament retract when changing layer: nil, nil overridden
was nil (inherited)
filament retraction distances when cut: nil, nil overridden
filament retraction minimum travel: nil, nil overridden
was nil (inherited)
filament soluble: 0 inherited
filament wipe: nil, nil overridden
was nil (inherited)
filament wipe distance: nil, nil overridden
was nil (inherited)
filament z hop: nil, nil overridden
was nil (inherited)
filament z hop types: nil, nil overridden
was nil (inherited)
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
long retractions when ec: 1, 1 overridden
nozzle temperature range high: 270 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 80 inherited
overhang fan threshold: 25% inherited
reduce fan stop start freq: 0 inherited
retraction distances when ec: 10, 10 overridden
setting id: GFSS98_11 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 100 inherited
volumetric speed coefficients: 0 0 0 0 0 0, 0 0 0 0 0 0 overridden

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "22.99"
  ],
  "filament_type": [
    "HIPS"
  ],
  "filament_wipe": [
    "nil",
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "90"
  ],
  "filament_z_hop": [
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.06"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240",
    "240"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "1",
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "90"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil",
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "6"
  ],
  "fan_cooling_layer_time": [
    "10"
  ],
  "filament_wipe_distance": [
    "nil",
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "nil",
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "90"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "0.5",
    "0.5"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "240",
    "240"
  ],
  "textured_plate_temp_initial_layer": [
    "90"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil"
  ],
  "filament_id": "GFS98",
  "supertack_plate_temp": [
    "0"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "filament_is_support": [
    "1"
  ],
  "setting_id": "GFSS98_11",
  "compatible_printers": [
    "Bambu Lab H2D Pro 0.2 nozzle"
  ],
  "filament_flush_temp": [
    "0",
    "0"
  ],
  "long_retractions_when_ec": [
    "1",
    "1"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow"
  ],
  "filament_ramming_travel_time": [
    "0",
    "0"
  ],
  "retraction_distances_when_ec": [
    "10",
    "10"
  ],
  "volumetric_speed_coefficients": [
    "0 0 0 0 0 0",
    "0 0 0 0 0 0"
  ],
  "filament_flush_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed": [
    "-1",
    "-1"
  ],
  "filament_adaptive_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "nil",
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil",
    "nil"
  ],
  "name": "Generic HIPS @BBL H2DP 0.2 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:05