Bambu PETG HF @BBL H2C

Bambu Lab · PETG · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Bambu PETG HF @base

→

Bambu PETG HF @BBL H2C

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

fdm_filament_template_direct_dual

Compatible printers (1)

Bambu Lab H2C 0.4 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Bambu Lab inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.28 inherited
Cost (/kg): 24.99 inherited

Print temperature

Nozzle (initial layer) (°C): 245 overridden
was 230 (inherited)
Nozzle (other layers) (°C): 245 overridden
was 245 (inherited)

Cooling

Fan minimum (%): 20 overridden
was 10 (inherited)
Fan maximum (%): 40 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 20 overridden
was 30 (inherited)
Slow down if layer below (sec): 10 overridden
was 12 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 0.97 overridden
was 0.95 (inherited)
Max volumetric speed (mm³/s): 25 overridden
was 21 (inherited)

Retraction

Retraction length (mm): 0.4 overridden
was nil (inherited)
Retraction speed (mm/s): nil via fdm_filament_template_direct_dual
Deretraction speed (mm/s): nil via fdm_filament_template_direct_dual

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	70 inherited	70 inherited
High Temp Plate	70 inherited	70 inherited
Textured PEI Plate	70 inherited	70 inherited
Cool Plate SuperTack	60 overridden	60 overridden

Other settings

additional fan full speed layer: 0 inherited
close additional fan first x layers: 3 inherited
compatible printers: Bambu Lab H2C 0.4 nozzle overridden
counter coef 2: 0.0058 overridden
counter coef 3: 0.0107 overridden
counter limit max: 0.15 overridden
counter limit min: 0.01 overridden
filament adaptive volumetric speed: 0, 0 via fdm_filament_template_direct_dual
filament bridge speed: 25, 25 via fdm_filament_template_direct_dual
filament change length: 4 overridden
was 12 (inherited)
filament change length nc: 4 overridden
filament cooling before tower: 10, 10 overridden
filament enable overhang speed: 1, 1 via fdm_filament_template_direct_dual
filament extruder variant: Direct Drive Standard, Direct Drive High Flow via fdm_filament_template_direct_dual
filament flush temp: 0, 0 via fdm_filament_template_direct_dual
filament flush volumetric speed: 0, 0 via fdm_filament_template_direct_dual
filament id: GFG02 inherited
filament is support: 0 inherited
filament long retractions when cut: nil, nil via fdm_filament_template_direct_dual
filament metal stickiness: High inherited
filament minimal purge on wipe tower: 15 inherited
filament overhang 1 4 speed: 0, 0 via fdm_filament_template_direct_dual
filament overhang 2 4 speed: 50, 50 via fdm_filament_template_direct_dual
filament overhang 3 4 speed: 30, 30 via fdm_filament_template_direct_dual
filament overhang 4 4 speed: 10, 10 via fdm_filament_template_direct_dual
filament overhang totally speed: 10, 10 via fdm_filament_template_direct_dual
filament pre cooling temperature: 0, 0 via fdm_filament_template_direct_dual
filament pre cooling temperature nc: 205, 205 overridden
filament prime volume: 30 inherited
filament prime volume nc: 30 overridden
filament ramming travel time: 0, 0 overridden
filament ramming travel time nc: 2, 2 overridden
filament ramming volumetric speed: -1, -1 via fdm_filament_template_direct_dual
filament ramming volumetric speed nc: -1, -1 via fdm_filament_template_direct_dual
filament retract before wipe: nil, nil via fdm_filament_template_direct_dual
filament retract length nc: 18, 18 overridden
filament retract restart extra: nil, nil via fdm_filament_template_direct_dual
filament retract when changing layer: nil, nil via fdm_filament_template_direct_dual
filament retraction distances when cut: nil, nil via fdm_filament_template_direct_dual
filament retraction minimum travel: nil, nil via fdm_filament_template_direct_dual
filament soluble: 0 inherited
filament tower ironing area: 8 overridden
filament wipe: 1, 1 overridden
was nil (inherited)
filament wipe distance: 1, 1 overridden
was nil (inherited)
filament z hop: nil, nil via fdm_filament_template_direct_dual
filament z hop types: Spiral Lift, Spiral Lift overridden
first x layer fan speed: 0 overridden
full fan speed layer: 0 inherited
hole coef 2: -0.0042 overridden
hole coef 3: 0.2006 overridden
hole limit max: 0.2 overridden
hole limit min: 0.09 overridden
impact strength z: 10.6 inherited
instantiation: true overridden
was false (inherited)
long retractions when ec: 1, 1 via fdm_filament_template_direct_dual
nozzle temperature range high: 270 inherited
nozzle temperature range low: 230 inherited
overhang fan speed: 100 overridden
was 90 (inherited)
overhang fan threshold: 10% inherited
override process overhang speed: 0, 0 via fdm_filament_template_direct_dual
pre start fan time: 2 overridden
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
retraction distances when ec: 10, 10 via fdm_filament_template_direct_dual
setting id: GFSG02_25 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 55 overridden
was 80 (inherited)
volumetric speed coefficients: 0 0 0 0 0 0, 0 0 0 0 0 0 via fdm_filament_template_direct_dual

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "40"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "24.99"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "1",
    "1"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "1.28"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "245",
    "245"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.97",
    "0.97"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20",
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_wipe_distance": [
    "1",
    "1"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "55"
  ],
  "filament_retraction_length": [
    "0.4",
    "0.6"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "25",
    "35"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "245",
    "245"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "filament_id": "GFG02",
  "impact_strength_z": [
    "10.6"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "filament_prime_volume": [
    "30"
  ],
  "filament_change_length": [
    "4"
  ],
  "filament_metal_stickiness": [
    "High"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_flush_temp": [
    "0",
    "0"
  ],
  "filament_z_hop_types": [
    "Spiral Lift",
    "Spiral Lift"
  ],
  "filament_bridge_speed": [
    "25",
    "25"
  ],
  "long_retractions_when_ec": [
    "1",
    "1"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow"
  ],
  "filament_retract_length_nc": [
    "18",
    "18"
  ],
  "filament_overhang_1_4_speed": [
    "0",
    "0"
  ],
  "filament_overhang_2_4_speed": [
    "50",
    "50"
  ],
  "filament_overhang_3_4_speed": [
    "30",
    "30"
  ],
  "filament_overhang_4_4_speed": [
    "10",
    "10"
  ],
  "retraction_distances_when_ec": [
    "10",
    "10"
  ],
  "filament_cooling_before_tower": [
    "10",
    "10"
  ],
  "volumetric_speed_coefficients": [
    "0 0 0 0 0 0",
    "0 0 0 0 0 0"
  ],
  "filament_enable_overhang_speed": [
    "1",
    "1"
  ],
  "filament_flush_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_overhang_totally_speed": [
    "10",
    "10"
  ],
  "filament_ramming_travel_time_nc": [
    "2",
    "2"
  ],
  "override_process_overhang_speed": [
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed": [
    "-1",
    "-1"
  ],
  "filament_adaptive_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "nil",
    "nil"
  ],
  "filament_pre_cooling_temperature_nc": [
    "205",
    "205"
  ],
  "filament_ramming_volumetric_speed_nc": [
    "-1",
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "nil",
    "nil"
  ],
  "setting_id": "GFSG02_25",
  "hole_coef_2": [
    "-0.0042"
  ],
  "hole_coef_3": [
    "0.2006"
  ],
  "counter_coef_2": [
    "0.0058"
  ],
  "counter_coef_3": [
    "0.0107"
  ],
  "hole_limit_max": [
    "0.2"
  ],
  "hole_limit_min": [
    "0.09"
  ],
  "counter_limit_max": [
    "0.15"
  ],
  "counter_limit_min": [
    "0.01"
  ],
  "pre_start_fan_time": [
    "2"
  ],
  "compatible_printers": [
    "Bambu Lab H2C 0.4 nozzle"
  ],
  "supertack_plate_temp": [
    "60"
  ],
  "first_x_layer_fan_speed": [
    "0"
  ],
  "filament_prime_volume_nc": [
    "30"
  ],
  "filament_change_length_nc": [
    "4"
  ],
  "filament_tower_ironing_area": [
    "8"
  ],
  "filament_ramming_travel_time": [
    "0",
    "0"
  ],
  "supertack_plate_temp_initial_layer": [
    "60"
  ],
  "name": "Bambu PETG HF @BBL H2C"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:15