Bambu PA6-GF @BBL X2D

Bambu Lab · PA-GF · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

Bambu PA6-GF @base

→

Bambu PA6-GF @BBL X2D

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

fdm_filament_template_direct_bowden

Compatible printers (2)

Bambu Lab X2D 0.6 nozzle
Bambu Lab X2D 0.8 nozzle

Settings

Basic information

Material variant: PA-GF inherited
Vendor: Bambu Lab inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.14 inherited
Cost (/kg): 59.99 inherited

Print temperature

Nozzle (initial layer) (°C): 265 overridden
was 290 (inherited)
Nozzle (other layers) (°C): 265 overridden
was 290 (inherited)

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 30 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 5 inherited
Slow down if layer below (sec): 2 inherited
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 0.96 overridden
was 0.96 (inherited)
Max volumetric speed (mm³/s): 10.5 overridden
was 8 (inherited)

Retraction

Retraction length (mm): 1 overridden
was nil (inherited)
Retraction speed (mm/s): nil via fdm_filament_template_direct_bowden
Deretraction speed (mm/s): nil via fdm_filament_template_direct_bowden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	95 inherited	95 inherited
High Temp Plate	95 inherited	95 inherited

Other settings

additional fan full speed layer: 2 inherited
chamber temperatures: 60 overridden
close additional fan first x layers: 3 inherited
compatible printers: Bambu Lab X2D 0.6 nozzle, Bambu Lab X2D 0.8 nozzle overridden
description: When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials. inherited
filament adaptive volumetric speed: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament bridge speed: 25, 25, 25, 25 via fdm_filament_template_direct_bowden
filament cooling before tower: 10, 10, 10, 10 overridden
filament enable overhang speed: 1, 1, 1, 1 via fdm_filament_template_direct_bowden
filament extruder variant: Direct Drive Standard, Direct Drive High Flow, Bowden Standard, Bowden High Flow via fdm_filament_template_direct_bowden
filament flush temp: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament flush volumetric speed: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament id: GFN08 inherited
filament is support: 0 inherited
filament long retractions when cut: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament minimal purge on wipe tower: 15 inherited
filament overhang 1 4 speed: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament overhang 2 4 speed: 50, 50, 50, 50 via fdm_filament_template_direct_bowden
filament overhang 3 4 speed: 30, 30, 30, 30 via fdm_filament_template_direct_bowden
filament overhang 4 4 speed: 10, 10, 10, 10 via fdm_filament_template_direct_bowden
filament overhang totally speed: 10, 10, 10, 10 via fdm_filament_template_direct_bowden
filament pre cooling temperature: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament pre cooling temperature nc: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament ramming travel time: 0, 0, 0, 0 overridden
filament ramming travel time nc: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
filament ramming volumetric speed: -1, -1, -1, -1 via fdm_filament_template_direct_bowden
filament ramming volumetric speed nc: -1, -1, -1, -1 via fdm_filament_template_direct_bowden
filament retract before wipe: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament retract length nc: 14, 14, 14, 14 via fdm_filament_template_direct_bowden
filament retract restart extra: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament retract when changing layer: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament retraction distances when cut: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament retraction minimum travel: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament soluble: 0 inherited
filament tower interface print temp: 265 overridden
filament wipe: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament wipe distance: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament z hop: nil, nil, nil, nil via fdm_filament_template_direct_bowden
filament z hop types: nil, nil, nil, nil via fdm_filament_template_direct_bowden
full fan speed layer: 2 inherited
impact strength z: 4.1 inherited
instantiation: true overridden
was false (inherited)
long retractions when ec: 1, 1, 1, 1 via fdm_filament_template_direct_bowden
nozzle temperature range high: 300 inherited
nozzle temperature range low: 270 inherited
overhang fan speed: 40 inherited
overhang fan threshold: 0% inherited
override process overhang speed: 0, 0, 0, 0 via fdm_filament_template_direct_bowden
reduce fan stop start freq: 0 inherited
required nozzle HRC: 3 inherited
retraction distances when ec: 3, 3, 4, 4 overridden
setting id: GFSN08_07 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 180 inherited
volumetric speed coefficients: 0 0 0 0 0 0, 0 0 0 0 0 0, 0 0 0 0 0 0, 0 0 0 0 0 0 via fdm_filament_template_direct_bowden

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "59.99"
  ],
  "filament_type": [
    "PA-GF"
  ],
  "filament_wipe": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "95"
  ],
  "filament_z_hop": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "95"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "1.14"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "265",
    "265",
    "265",
    "265"
  ],
  "overhang_fan_speed": [
    "40"
  ],
  "filament_flow_ratio": [
    "0.96",
    "0.96",
    "0.96",
    "0.96"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20",
    "20",
    "20",
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "full_fan_speed_layer": [
    "2"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "fan_cooling_layer_time": [
    "5"
  ],
  "filament_wipe_distance": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "overhang_fan_threshold": [
    "0%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "180"
  ],
  "filament_retraction_length": [
    "1",
    "nil",
    "nil",
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "95"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "95"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "10.5",
    "10.5",
    "10.5",
    "10.5"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "2"
  ],
  "nozzle_temperature_initial_layer": [
    "265",
    "265",
    "265",
    "265"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "270"
  ],
  "nozzle_temperature_range_high": [
    "300"
  ],
  "description": "When printing this filament, there's a risk of nozzle clogging, oozing, warping and low layer adhesion strength. To get better results, please refer to this wiki: Printing Tips for High Temp / Engineering materials.",
  "filament_id": "GFN08",
  "impact_strength_z": [
    "4.1"
  ],
  "filament_flush_temp": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_z_hop_types": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "filament_bridge_speed": [
    "25",
    "25",
    "25",
    "25"
  ],
  "long_retractions_when_ec": [
    "1",
    "1",
    "1",
    "1"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow",
    "Bowden Standard",
    "Bowden High Flow"
  ],
  "filament_retract_length_nc": [
    "14",
    "14",
    "14",
    "14"
  ],
  "filament_overhang_1_4_speed": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_overhang_2_4_speed": [
    "50",
    "50",
    "50",
    "50"
  ],
  "filament_overhang_3_4_speed": [
    "30",
    "30",
    "30",
    "30"
  ],
  "filament_overhang_4_4_speed": [
    "10",
    "10",
    "10",
    "10"
  ],
  "retraction_distances_when_ec": [
    "3",
    "3",
    "4",
    "4"
  ],
  "filament_cooling_before_tower": [
    "10",
    "10",
    "10",
    "10"
  ],
  "volumetric_speed_coefficients": [
    "0 0 0 0 0 0",
    "0 0 0 0 0 0",
    "0 0 0 0 0 0",
    "0 0 0 0 0 0"
  ],
  "filament_enable_overhang_speed": [
    "1",
    "1",
    "1",
    "1"
  ],
  "filament_flush_volumetric_speed": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_overhang_totally_speed": [
    "10",
    "10",
    "10",
    "10"
  ],
  "filament_ramming_travel_time_nc": [
    "0",
    "0",
    "0",
    "0"
  ],
  "override_process_overhang_speed": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed": [
    "-1",
    "-1",
    "-1",
    "-1"
  ],
  "filament_adaptive_volumetric_speed": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "filament_pre_cooling_temperature_nc": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed_nc": [
    "-1",
    "-1",
    "-1",
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "nil",
    "nil",
    "nil",
    "nil"
  ],
  "setting_id": "GFSN08_07",
  "compatible_printers": [
    "Bambu Lab X2D 0.6 nozzle",
    "Bambu Lab X2D 0.8 nozzle"
  ],
  "chamber_temperatures": [
    "60"
  ],
  "filament_ramming_travel_time": [
    "0",
    "0",
    "0",
    "0"
  ],
  "filament_tower_interface_print_temp": [
    "265"
  ],
  "name": "Bambu PA6-GF @BBL X2D"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:15