Creality Generic PLA Silk @K2-all

QIDI · PLA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Creality Generic PLA

→

Creality Generic PLA @K2-all

→

Creality Generic PLA Silk @K2-all

Compatible printers (12)

Creality K2 0.2 nozzle
Creality K2 0.4 nozzle
Creality K2 0.6 nozzle
Creality K2 0.8 nozzle
Creality K2 Plus 0.2 nozzle
Creality K2 Plus 0.4 nozzle
Creality K2 Plus 0.6 nozzle
Creality K2 Plus 0.8 nozzle
Creality K2 Pro 0.2 nozzle
Creality K2 Pro 0.4 nozzle
Creality K2 Pro 0.6 nozzle
Creality K2 Pro 0.8 nozzle

Settings

Basic information

Material variant: PLA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 220 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 4 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 10 overridden
was 18 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Custom G-code

filament_start_gcode inherited

;filament start gcode
{if (position[2] > first_layer_height) }
M104 S[nozzle_temperature]
{else} 
M104 S[first_layer_temperature]
{endif}

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Creality K2 0.2 nozzle, Creality K2 0.4 nozzle, Creality K2 0.6 nozzle, Creality K2 0.8 nozzle, Creality K2 Plus 0.2 nozzle, Creality K2 Plus 0.4 nozzle, Creality K2 Plus 0.6 nozzle, Creality K2 Plus 0.8 nozzle, Creality K2 Pro 0.2 nozzle, Creality K2 Pro 0.4 nozzle, Creality K2 Pro 0.6 nozzle, Creality K2 Pro 0.8 nozzle overridden
was Creality K2 0.2 nozzle, Creality K2 0.4 nozzle, Creality K2 0.6 nozzle, Creality K2 0.8 nozzle, Creality K2 Plus 0.2 nozzle, Creality K2 Plus 0.4 nozzle, Creality K2 Plus 0.6 nozzle, Creality K2 Plus 0.8 nozzle, Creality K2 Pro 0.2 nozzle, Creality K2 Pro 0.4 nozzle, Creality K2 Pro 0.6 nozzle, Creality K2 Pro 0.8 nozzle (inherited)
filament id: GFL99 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSL96_00 overridden
was GFSL99_00 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    ";filament start gcode\n{if (position[2] > first_layer_height) }\nM104 S[nozzle_temperature]\n{else} \nM104 S[first_layer_temperature]\n{endif}"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "10"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "setting_id": "GFSL96_00",
  "filament_id": "GFL99",
  "compatible_printers": [
    "Creality K2 0.2 nozzle",
    "Creality K2 0.4 nozzle",
    "Creality K2 0.6 nozzle",
    "Creality K2 0.8 nozzle",
    "Creality K2 Plus 0.2 nozzle",
    "Creality K2 Plus 0.4 nozzle",
    "Creality K2 Plus 0.6 nozzle",
    "Creality K2 Plus 0.8 nozzle",
    "Creality K2 Pro 0.2 nozzle",
    "Creality K2 Pro 0.4 nozzle",
    "Creality K2 Pro 0.6 nozzle",
    "Creality K2 Pro 0.8 nozzle"
  ],
  "name": "Creality Generic PLA Silk @K2-all"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:01