Creality Generic ASA @K1-all

QIDI · ASA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

Creality Generic ASA

→

Creality Generic ASA @K1-all

Compatible printers (4)

Creality K1C 0.4 nozzle
Creality K1C 0.6 nozzle
Creality K1C 0.8 nozzle
Creality K1 SE 0.4 nozzle

Settings

Basic information

Material variant: ASA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 260 inherited
Nozzle (other layers) (°C): 250 inherited

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 60 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 35 inherited
Slow down if layer below (sec): 3 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 30 (inherited)

Flow

Flow ratio: 0.926 inherited
Max volumetric speed (mm³/s): 12 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	105 inherited	105 inherited
Textured PEI Plate	105 inherited	105 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Creality K1C 0.4 nozzle, Creality K1C 0.6 nozzle, Creality K1C 0.8 nozzle, Creality K1 SE 0.4 nozzle overridden
was Creality CR-10 V2 0.4 nozzle, Creality CR-10 V3 0.4 nozzle, Creality CR-10 V3 0.6 nozzle, Creality CR-10 Max 0.4 nozzle, Creality CR-6 SE 0.2 nozzle, Creality CR-6 SE 0.4 nozzle, Creality CR-6 SE 0.6 nozzle, Creality CR-6 SE 0.8 nozzle, Creality CR-6 Max 0.2 nozzle, Creality CR-6 Max 0.4 nozzle, Creality CR-6 Max 0.6 nozzle, Creality CR-6 Max 0.8 nozzle, Creality Ender-3 V2 0.4 nozzle, Creality Ender-3 0.2 nozzle, Creality Ender-3 0.4 nozzle, Creality Ender-3 0.6 nozzle, Creality Ender-3 0.8 nozzle, Creality Ender-3 Pro 0.2 nozzle, Creality Ender-3 Pro 0.4 nozzle, Creality Ender-3 Pro 0.6 nozzle, Creality Ender-3 Pro 0.8 nozzle, Creality Ender-3 V2 Neo 0.4 nozzle, Creality Ender-3 S1 0.4 nozzle, Creality Ender-3 S1 Pro 0.4 nozzle, Creality Ender-5 0.4 nozzle, Creality Ender-5 Plus 0.4 nozzle, Creality Ender-5 Pro (2019) 0.2 nozzle, Creality Ender-5 Pro (2019) 0.25 nozzle, Creality Ender-5 Pro (2019) 0.3 nozzle, Creality Ender-5 Pro (2019) 0.4 nozzle, Creality Ender-5 Pro (2019) 0.5 nozzle, Creality Ender-5 Pro (2019) 0.6 nozzle, Creality Ender-5 Pro (2019) 0.8 nozzle, Creality Ender-5 Pro (2019) 1.0 nozzle, Creality Ender-5S 0.4 nozzle, Creality Ender-5 S1 0.4 nozzle, Creality Ender-6 0.4 nozzle, Creality K1 (0.4 nozzle), Creality K1 (0.6 nozzle), Creality K1 (0.8 nozzle), Creality K1 Max (0.4 nozzle), Creality K1 Max (0.6 nozzle), Creality K1 Max (0.8 nozzle) (inherited)
filament id: GFB98 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 80 inherited
overhang fan threshold: 25% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04_00 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "0.926"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "3"
  ],
  "fan_cooling_layer_time": [
    "35"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "setting_id": "GFSA04_00",
  "filament_id": "GFB98",
  "compatible_printers": [
    "Creality K1C 0.4 nozzle",
    "Creality K1C 0.6 nozzle",
    "Creality K1C 0.8 nozzle",
    "Creality K1 SE 0.4 nozzle"
  ],
  "name": "Creality Generic ASA @K1-all"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:01