Creality Generic PETG @Hi-all

QIDI · PETG · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Creality Generic PETG

→

Creality Generic PETG @Hi-all

Compatible printers (2)

Creality Hi 0.4 nozzle
Creality Hi 0.6 nozzle

Inherited from this (1)

Creality Generic PETG-CF @Hi-all

Settings

Basic information

Material variant: PETG inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 250 overridden
was 255 (inherited)

Cooling

Fan minimum (%): 40 inherited
Fan maximum (%): 90 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 5 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 9 overridden
was 10 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	70 overridden was 60	70 overridden was 60
Engineering Plate	70 overridden was 70	70 overridden was 0
High Temp Plate	70 overridden was 70	70 overridden was 80
Textured PEI Plate	70 overridden was 70	70 overridden was 80

Custom G-code

filament_start_gcode overridden

; filament start gcode
{if (position[2] > first_layer_height) }
M104 S[nozzle_temperature]
{else}
M104 S[first_layer_temperature]
{endif}

Other settings

bed type: Cool Plate inherited
compatible printers: Creality Hi 0.4 nozzle, Creality Hi 0.6 nozzle overridden
was Creality CR-10 V2 0.4 nozzle, Creality CR-10 V3 0.4 nozzle, Creality CR-10 V3 0.6 nozzle, Creality CR-10 Max 0.4 nozzle, Creality CR-6 SE 0.2 nozzle, Creality CR-6 SE 0.4 nozzle, Creality CR-6 SE 0.6 nozzle, Creality CR-6 SE 0.8 nozzle, Creality CR-6 Max 0.2 nozzle, Creality CR-6 Max 0.4 nozzle, Creality CR-6 Max 0.6 nozzle, Creality CR-6 Max 0.8 nozzle, Creality Sermoon V1 0.4 nozzle, Creality Ender-3 0.2 nozzle, Creality Ender-3 0.4 nozzle, Creality Ender-3 0.6 nozzle, Creality Ender-3 0.8 nozzle, Creality Ender-3 Pro 0.2 nozzle, Creality Ender-3 Pro 0.4 nozzle, Creality Ender-3 Pro 0.6 nozzle, Creality Ender-3 Pro 0.8 nozzle, Creality Ender-3 V2 0.4 nozzle, Creality Ender-3 V2 Neo 0.4 nozzle, Creality Ender-3 S1 0.4 nozzle, Creality Ender-3 S1 Pro 0.4 nozzle, Creality Ender-3 S1 Plus 0.2 nozzle, Creality Ender-3 S1 Plus 0.4 nozzle, Creality Ender-3 S1 Plus 0.6 nozzle, Creality Ender-3 S1 Plus 0.8 nozzle, Creality Ender-5 0.4 nozzle, Creality Ender-5 Plus 0.4 nozzle, Creality Ender-5 Pro (2019) 0.2 nozzle, Creality Ender-5 Pro (2019) 0.25 nozzle, Creality Ender-5 Pro (2019) 0.3 nozzle, Creality Ender-5 Pro (2019) 0.4 nozzle, Creality Ender-5 Pro (2019) 0.5 nozzle, Creality Ender-5 Pro (2019) 0.6 nozzle, Creality Ender-5 Pro (2019) 0.8 nozzle, Creality Ender-5 Pro (2019) 1.0 nozzle, Creality Ender-5S 0.4 nozzle, Creality Ender-5 S1 0.4 nozzle, Creality Ender-6 0.4 nozzle, Creality K1 (0.4 nozzle), Creality K1 (0.6 nozzle), Creality K1 (0.8 nozzle), Creality K1 Max (0.4 nozzle), Creality K1 Max (0.6 nozzle), Creality K1 Max (0.8 nozzle), Creality CR-10 SE 0.2 nozzle, Creality CR-10 SE 0.4 nozzle, Creality CR-10 SE 0.6 nozzle, Creality CR-10 SE 0.8 nozzle, Creality CR-M4 0.4 nozzle (inherited)
filament id: GFG99 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 90 inherited
overhang fan threshold: 25% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSG99_00 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 80 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "90"
  ],
  "fan_min_speed": [
    "40"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "70"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n{if (position[2] > first_layer_height) }\nM104 S[nozzle_temperature]\n{else}\nM104 S[first_layer_temperature]\n{endif}\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "80"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "70"
  ],
  "filament_max_volumetric_speed": [
    "9"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "setting_id": "GFSG99_00",
  "filament_id": "GFG99",
  "compatible_printers": [
    "Creality Hi 0.4 nozzle",
    "Creality Hi 0.6 nozzle"
  ],
  "name": "Creality Generic PETG @Hi-all"
}

Version history

View full history with diffs →

v1 created 2026-05-19 05:01