QIDI PET-CF @Qidi X-Max 4 0.4 nozzle

QIDI · PET-CF · 0.40mm nozzle · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_x4_common

→

QIDI PET-CF@X-Max 4-Series

→

QIDI PET-CF @Qidi X-Max 4 0.4 nozzle

Compatible printers (1)

Qidi X-Max 4 0.4 nozzle

Settings

Basic information

Material variant: PET-CF inherited
Vendor: QIDI inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.3 inherited
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 280 inherited
Nozzle (other layers) (°C): 280 inherited
Chamber (°C): 0 inherited

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 30 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 5 inherited
Slow down if layer below (sec): 2 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 8 inherited

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	80 inherited	80 inherited
Cool Plate SuperTack	80 inherited	80 inherited

Other settings

activate air filtration: 1 inherited
additional cooling fan speed: 0 inherited
additional cooling fan speed unseal: 0 inherited
bed type: Cool Plate inherited
box temperature: 55 inherited
box temperature range high: 65 inherited
box temperature range low: 0 inherited
compatible printers: Qidi X-Max 4 0.4 nozzle overridden
was — (inherited)
complete print exhaust fan speed: 0 inherited
during print exhaust fan speed: 100 inherited
enable pressure advance: 1 inherited
filament adhesiveness category: 800 inherited
filament cooling before tower: 10 inherited
filament flush temp: 0 inherited
filament flush volumetric speed: 0 inherited
filament id: QD_3_1_37 inherited
filament long retractions when ec: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament pre cooling temperature: 0 inherited
filament prime volume: 30 inherited
filament ramming travel time: 0 inherited
filament ramming volumetric speed: -1 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when ec: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament velocity adaptation factor: 1 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
impact strength z: 4.5 inherited
instantiation: true overridden
was false (inherited)
no slow down for cooling on outwalls: 0 inherited
nozzle temperature range high: 320 inherited
nozzle temperature range low: 280 inherited
overhang fan speed: 40 inherited
overhang fan threshold: 0% inherited
pressure advance: 0.032 inherited
reduce fan stop start freq: 1 inherited
setting id: GFSN99 overridden
was GFSN99 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 185 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PET-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "box_temperature": [
    "55"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "QIDI"
  ],
  "filament_density": [
    "1.3"
  ],
  "filament_soluble": [
    "0"
  ],
  "pressure_advance": [
    "0.032"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament"
  ],
  "nozzle_temperature": [
    "280"
  ],
  "overhang_fan_speed": [
    "40"
  ],
  "chamber_temperature": [
    "0"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_flush_temp": [
    "0"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament start gcode"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "supertack_plate_temp": [
    "80"
  ],
  "filament_prime_volume": [
    "30"
  ],
  "fan_cooling_layer_time": [
    "5"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "0%"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "box_temperature_range_low": [
    "0"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "185"
  ],
  "box_temperature_range_high": [
    "65"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_ramming_travel_time": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_cooling_before_tower": [
    "10"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "during_print_exhaust_fan_speed": [
    "100"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_flush_volumetric_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "280"
  ],
  "filament_long_retractions_when_ec": [
    "nil"
  ],
  "filament_ramming_volumetric_speed": [
    "-1"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "80"
  ],
  "additional_cooling_fan_speed_unseal": [
    "0"
  ],
  "filament_velocity_adaptation_factor": [
    "1"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "no_slow_down_for_cooling_on_outwalls": [
    "0"
  ],
  "filament_retraction_distances_when_ec": [
    "nil"
  ],
  "setting_id": "GFSN99",
  "filament_id": "QD_3_1_37",
  "impact_strength_z": [
    "4.5"
  ],
  "compatible_printers": [
    "Qidi X-Max 4 0.4 nozzle"
  ],
  "nozzle_temperature_range_low": [
    "280"
  ],
  "nozzle_temperature_range_high": [
    "320"
  ],
  "filament_adhesiveness_category": [
    "800"
  ],
  "name": "QIDI PET-CF @Qidi X-Max 4 0.4 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:58