QIDI ASA-Aero@X-Max 4-Series

QIDI · ASA-AERO · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_x4_common

→

QIDI ASA-Aero@X-Max 4-Series

Inherited from this (1)

QIDI ASA-Aero @Qidi X-Max 4 0.4 nozzle

Settings

Basic information

Material variant: ASA-AERO overridden
was PLA (inherited)
Vendor: QIDI inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.03 overridden
was 1.24 (inherited)
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 210 (inherited)
Nozzle (other layers) (°C): 260 overridden
was 210 (inherited)
Chamber (°C): 60 overridden
was 0 (inherited)

Cooling

Fan minimum (%): 10 overridden
was 100 (inherited)
Fan maximum (%): 50 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 40 overridden
was 60 (inherited)
Slow down if layer below (sec): 4 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.7 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 24.5 (inherited)

Retraction

Retraction length (mm): 0.01 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	90 overridden was 60	90 overridden was 60
Cool Plate SuperTack	0 inherited	0 inherited

Other settings

activate air filtration: 1 inherited
additional cooling fan speed: 0 inherited
additional cooling fan speed unseal: 0 inherited
bed type: Cool Plate inherited
box temperature: 0 inherited
box temperature range high: 45 overridden
was 0 (inherited)
box temperature range low: 0 inherited
complete print exhaust fan speed: 0 inherited
during print exhaust fan speed: 0 overridden
was 100 (inherited)
enable pressure advance: 1 inherited
filament adhesiveness category: 200 overridden
filament cooling before tower: 10 inherited
filament flush temp: 0 inherited
filament flush volumetric speed: 0 inherited
filament id: QD_3_1_19 overridden
filament long retractions when ec: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament pre cooling temperature: 0 inherited
filament prime volume: 30 inherited
filament ramming travel time: 0 inherited
filament ramming volumetric speed: -1 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: 0 overridden
was nil (inherited)
filament retraction distances when ec: nil inherited
filament retraction minimum travel: 0 overridden
was nil (inherited)
filament soluble: 0 inherited
filament velocity adaptation factor: 1 inherited
filament wipe: 0 overridden
was nil (inherited)
filament wipe distance: nil inherited
filament z hop: 0 overridden
was nil (inherited)
filament z hop types: nil inherited
full fan speed layer: 0 inherited
impact strength z: 3.4 overridden
instantiation: false overridden
was false (inherited)
no slow down for cooling on outwalls: 0 inherited
nozzle temperature range high: 280 overridden
nozzle temperature range low: 240 overridden
overhang fan speed: 80 overridden
was 100 (inherited)
overhang fan threshold: 25% overridden
was 95% (inherited)
pressure advance: 0.021 overridden
was 0.042 (inherited)
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 100 overridden
was 100 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "ASA-AERO"
  ],
  "filament_wipe": [
    "0"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "0"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "box_temperature": [
    "0"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "QIDI"
  ],
  "filament_density": [
    "1.03"
  ],
  "filament_soluble": [
    "0"
  ],
  "pressure_advance": [
    "0.021"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "chamber_temperature": [
    "60"
  ],
  "filament_flow_ratio": [
    "0.7"
  ],
  "filament_flush_temp": [
    "0"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament start gcode"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "supertack_plate_temp": [
    "0"
  ],
  "filament_prime_volume": [
    "30"
  ],
  "fan_cooling_layer_time": [
    "40"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "box_temperature_range_low": [
    "0"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "box_temperature_range_high": [
    "45"
  ],
  "filament_retraction_length": [
    "0.01"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_ramming_travel_time": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_cooling_before_tower": [
    "10"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "during_print_exhaust_fan_speed": [
    "0"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_flush_volumetric_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "filament_long_retractions_when_ec": [
    "nil"
  ],
  "filament_ramming_volumetric_speed": [
    "-1"
  ],
  "filament_retraction_minimum_travel": [
    "0"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "additional_cooling_fan_speed_unseal": [
    "0"
  ],
  "filament_velocity_adaptation_factor": [
    "1"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "0"
  ],
  "no_slow_down_for_cooling_on_outwalls": [
    "0"
  ],
  "filament_retraction_distances_when_ec": [
    "nil"
  ],
  "setting_id": "GFSA04",
  "filament_id": "QD_3_1_19",
  "impact_strength_z": [
    "3.4"
  ],
  "compatible_printers": [],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "filament_adhesiveness_category": [
    "200"
  ],
  "name": "QIDI ASA-Aero@X-Max 4-Series"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:58