fdm_filament_hips

Generic · HIPS · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_hips

Inherited from this (1)

Generic HIPS @base

Settings

Basic information

Material variant: HIPS overridden
was PLA (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.06 overridden
was 0 (inherited)
Cost (/kg): 22.99 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 200 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 200 (inherited)

Cooling

Fan minimum (%): 0 overridden
was 35 (inherited)
Fan maximum (%): 60 overridden
was 100 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 10 overridden
was 60 (inherited)
Slow down if layer below (sec): 6 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 8 overridden
was 0 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 60	0 overridden was 60
Engineering Plate	90 overridden was 60	90 overridden was 60
High Temp Plate	90 overridden was 60	90 overridden was 60
Textured PEI Plate	90 overridden	90 overridden
Cool Plate SuperTack	0 overridden	0 overridden

Other settings

additional fan full speed layer: 0 inherited
close additional fan first x layers: 3 inherited
filament adhesiveness category: 798 overridden
filament dev ams drying heat distortion temperature: 90 overridden
filament dev ams drying temperature: 65, 80, 65, 75 overridden
filament dev ams drying time: 12, 12, 12, 12 overridden
filament dev drying cooling temperature: 75 overridden
filament dev drying softening temperature: 80 overridden
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 270 overridden
nozzle temperature range low: 220 overridden
overhang fan speed: 80 overridden
was 100 (inherited)
overhang fan threshold: 25% overridden
was 95% (inherited)
reduce fan stop start freq: 0 inherited
required nozzle HRC: 3 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 100 inherited

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "22.99"
  ],
  "filament_type": [
    "HIPS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "90"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.06"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n\n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "6"
  ],
  "fan_cooling_layer_time": [
    "10"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "90"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "textured_plate_temp": [
    "90"
  ],
  "supertack_plate_temp": [
    "0"
  ],
  "filament_dev_ams_drying_time": [
    "12",
    "12",
    "12",
    "12"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "filament_adhesiveness_category": [
    "798"
  ],
  "textured_plate_temp_initial_layer": [
    "90"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "filament_dev_ams_drying_temperature": [
    "65",
    "80",
    "65",
    "75"
  ],
  "filament_dev_drying_cooling_temperature": [
    "75"
  ],
  "filament_dev_drying_softening_temperature": [
    "80"
  ],
  "filament_dev_ams_drying_heat_distortion_temperature": [
    "90"
  ],
  "name": "fdm_filament_hips"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 04:16
v1 created 2026-05-19 04:01