QIDI ASA @Qidi Q1 Pro 0.8 nozzle

Generic · ASA · 0.80mm nozzle · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

QIDI ASA

→

QIDI ASA @Qidi Q1 Pro 0.8 nozzle

Compatible printers (1)

Qidi Q1 Pro 0.8 nozzle

Settings

Basic information

Material variant: ASA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.07 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 250 (inherited)
Nozzle (other layers) (°C): 255 overridden
was 270 (inherited)
Chamber (°C): 55 overridden
was 55 (inherited)

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 50 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 40 overridden
was 40 (inherited)
Slow down if layer below (sec): 4 overridden
was 4 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 30 (inherited)

Flow

Flow ratio: 0.92 inherited
Max volumetric speed (mm³/s): 13 overridden
was 16 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	90 inherited	90 inherited
Engineering Plate	90 inherited	90 inherited
High Temp Plate	90 inherited	90 inherited
Textured PEI Plate	90 inherited	90 inherited

Other settings

activate air filtration: 1 overridden
activate chamber temp control: 0 overridden
additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Qidi Q1 Pro 0.8 nozzle overridden
was Qidi X-Plus 0.2 nozzle, Qidi X-Max 0.2 nozzle, Qidi X-CF Pro 0.2 nozzle, Qidi X-Plus 0.4 nozzle, Qidi X-Max 0.4 nozzle, Qidi X-CF Pro 0.4 nozzle, Qidi X-Smart 3 0.4 nozzle, Qidi X-Plus 3 0.4 nozzle, Qidi X-Max 3 0.4 nozzle, Qidi X-Plus 0.6 nozzle, Qidi X-Max 0.6 nozzle, Qidi X-CF Pro 0.6 nozzle, Qidi X-Smart 3 0.6 nozzle, Qidi X-Plus 3 0.6 nozzle, Qidi X-Max 3 0.6 nozzle, Qidi X-Plus 0.8 nozzle, Qidi X-Max 0.8 nozzle, Qidi X-CF Pro 0.8 nozzle, Qidi X-Smart 3 0.8 nozzle, Qidi X-Plus 3 0.8 nozzle, Qidi X-Max 3 0.8 nozzle (inherited)
during print exhaust fan speed: 0 overridden
enable pressure advance: 1 inherited
filament id: GFB99 overridden
was GFB99 (inherited)
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 80 overridden
was 80 (inherited)
overhang fan threshold: 25% inherited
pressure advance: 0.011 overridden
was 0.021 (inherited)
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "90"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "90"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.07"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "0.92"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "90"
  ],
  "filament_settings_id": [
    "QIDI ASA @Qidi Q1 Pro 0.8 nozzle"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "fan_cooling_layer_time": [
    "40"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "90"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "90"
  ],
  "filament_max_volumetric_speed": [
    "13"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "90"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "pressure_advance": [
    "0.011"
  ],
  "chamber_temperature": [
    "55"
  ],
  "compatible_printers": [
    "Qidi Q1 Pro 0.8 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "during_print_exhaust_fan_speed": [
    "0"
  ],
  "name": "QIDI ASA @Qidi Q1 Pro 0.8 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:57