Prusament PVB @XL 5T

Generic · PVB · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pvb

→

Prusament PVB @XL 5T

Compatible printers (6)

Prusa XL 5T 0.25 nozzle
Prusa XL 5T 0.3 nozzle
Prusa XL 5T 0.4 nozzle
Prusa XL 5T 0.5 nozzle
Prusa XL 5T 0.6 nozzle
Prusa XL 5T 0.8 nozzle

Settings

Basic information

Material variant: PVB inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 215 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 100 overridden
was 100 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 1 overridden
was 1 (inherited)
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 10 overridden
was 4 (inherited)
Min speed when slowed (mm/s): 15 overridden
was 10 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 8 overridden
was 15 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	35 inherited	35 inherited
Engineering Plate	0 inherited	0 inherited
High Temp Plate	75 overridden was 45	75 overridden was 45
Textured PEI Plate	60 inherited	60 inherited

Custom G-code

filament_start_gcode overridden

; filament start gcode
M900 K{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.07{elsif nozzle_diameter[0]==0.35}0.06{elsif nozzle_diameter[0]==0.6}0.03{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.8}0.015{else}0{endif} ; Filament gcode

{if printer_notes=~/.*PRINTER_MODEL_XLIS.*/}
M572 S{if nozzle_diameter[0]==0.4}0.036{elsif nozzle_diameter[0]==0.5}0.025{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.014{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.08{else}0{endif} ; Filament gcode
{endif}

M142 S36 ; set heatbreak target temp

Other settings

additional cooling fan speed: 70 inherited
bed type: Cool Plate inherited
compatible printers: Prusa XL 5T 0.25 nozzle, Prusa XL 5T 0.3 nozzle, Prusa XL 5T 0.4 nozzle, Prusa XL 5T 0.5 nozzle, Prusa XL 5T 0.6 nozzle, Prusa XL 5T 0.8 nozzle overridden
filament cooling final speed: 3.5 overridden
filament cooling initial speed: 10 overridden
filament cooling moves: 2 overridden
filament id: GFS98 inherited
filament is support: 1 inherited
filament load time: 10.5 overridden
filament loading speed: 10 overridden
filament loading speed start: 50 overridden
filament minimal purge on wipe tower: 15 inherited
filament multitool ramming: 1 overridden
filament multitool ramming flow: 40 overridden
filament multitool ramming volume: 5 overridden
filament retract before wipe: nil inherited
filament retract lift below: 0.6 overridden
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 1 inherited
filament stamping distance: 45 overridden
filament stamping loading speed: 29 overridden
filament unload time: 8.5 overridden
filament unloading speed: 100 overridden
filament unloading speed start: 100 overridden
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 3 overridden
was 0 (inherited)
idle temperature: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature intial layer: 215 overridden
nozzle temperature range high: 250 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 overridden
was 100 (inherited)
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 50 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PVB"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": "75",
  "cool_plate_temp": [
    "35"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "1"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": "215",
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": "15",
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\nM900 K{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.07{elsif nozzle_diameter[0]==0.35}0.06{elsif nozzle_diameter[0]==0.6}0.03{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.8}0.015{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*PRINTER_MODEL_XLIS.*/}\nM572 S{if nozzle_diameter[0]==0.4}0.036{elsif nozzle_diameter[0]==0.5}0.025{elsif nozzle_diameter[0]==0.6}0.02{elsif nozzle_diameter[0]==0.8}0.014{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.08{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "50"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": "75",
  "cool_plate_temp_initial_layer": [
    "35"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_id": "GFS98",
  "idle_temperature": "0",
  "filament_is_support": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "setting_id": "GFSA04",
  "filament_load_time": "10.5",
  "compatible_printers": [
    "Prusa XL 5T 0.25 nozzle",
    "Prusa XL 5T 0.3 nozzle",
    "Prusa XL 5T 0.4 nozzle",
    "Prusa XL 5T 0.5 nozzle",
    "Prusa XL 5T 0.6 nozzle",
    "Prusa XL 5T 0.8 nozzle"
  ],
  "filament_unload_time": "8.5",
  "filament_cooling_moves": "2",
  "filament_loading_speed": "10",
  "filament_unloading_speed": "100",
  "filament_multitool_ramming": [
    "1"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "filament_retract_lift_below": "0.6",
  "filament_cooling_final_speed": "3.5",
  "filament_loading_speed_start": "50",
  "filament_cooling_initial_speed": "10",
  "filament_unloading_speed_start": "100",
  "filament_multitool_ramming_flow": [
    "40"
  ],
  "filament_stamping_loading_speed": [
    "29"
  ],
  "nozzle_temperature_intial_layer": "215",
  "filament_multitool_ramming_volume": [
    "5"
  ],
  "name": "Prusament PVB @XL 5T"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:55