Prusament PETG @CORE One

Prusa · PETG · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Prusament PETG @CORE One

Compatible printers (4)

Prusa CORE One 0.25 nozzle
Prusa CORE One 0.3 nozzle
Prusa CORE One 0.4 nozzle
Prusa CORE One 0.5 nozzle

Inherited from this (6)

Settings

Basic information

Material variant: PETG overridden
was PETG (inherited)
Vendor: Prusa Polymers overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.27 overridden
was 1.27 (inherited)
Cost (/kg): 29.99 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 250 overridden
was 255 (inherited)
Chamber (°C): 35 overridden

Cooling

Fan minimum (%): 30 overridden
was 20 (inherited)
Fan maximum (%): 60 overridden
was 80 (inherited)
Disable fan for first N layers: 3 overridden
was 3 (inherited)
Full fan if layer below (sec): 25 overridden
was 5 (inherited)
Slow down if layer below (sec): 9 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 15 overridden
was 10 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 25 (inherited)

Retraction

Retraction length (mm): 0.8 overridden
was nil (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	70 inherited	0 inherited
High Temp Plate	85 overridden was 70	85 overridden was 80
Textured PEI Plate	70 inherited	80 inherited

Custom G-code

filament_start_gcode overridden

M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Filament gcode

{if printer_notes=~/.*(MK4IS|XLIS|MK4S|MK3.9S|CORE One).*/}
M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.053{elsif nozzle_diameter[filament_extruder_id]==0.5}0.042{elsif nozzle_diameter[filament_extruder_id]==0.6}0.032{elsif nozzle_diameter[filament_extruder_id]==0.8}0.018{elsif nozzle_diameter[filament_extruder_id]==0.25}0.18{elsif nozzle_diameter[filament_extruder_id]==0.3}0.1{else}0{endif} ; Filament gcode
{endif}

M142 S36 ; set heatbreak target temp

Other settings

bed type: Cool Plate inherited
compatible printers: Prusa CORE One 0.25 nozzle, Prusa CORE One 0.3 nozzle, Prusa CORE One 0.4 nozzle, Prusa CORE One 0.5 nozzle overridden
filament id: Prusament PETG @CORE One overridden
filament minimal purge on wipe tower: 35 overridden
was 15 (inherited)
filament retract before wipe: 20 overridden
was nil (inherited)
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 overridden
was 0 (inherited)
filament wipe: 1 overridden
was nil (inherited)
filament wipe distance: nil inherited
filament z hop: 1.5 overridden
was nil (inherited)
filament z hop types: Slope Lift overridden
was nil (inherited)
full fan speed layer: 5 overridden
was 0 (inherited)
idle temperature: 130 overridden
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 60 overridden
was 70 (inherited)
overhang fan threshold: 95% inherited
reduce fan stop start freq: 1 overridden
was 1 (inherited)
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 80 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "29.99"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "1"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "1.5"
  ],
  "hot_plate_temp": [
    "85"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Prusa Polymers"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "60"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "textured_plate_temp": [
    "80"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.25}0.12{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS|MK4S|MK3.9S|CORE One).*/}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.053{elsif nozzle_diameter[filament_extruder_id]==0.5}0.042{elsif nozzle_diameter[filament_extruder_id]==0.6}0.032{elsif nozzle_diameter[filament_extruder_id]==0.8}0.018{elsif nozzle_diameter[filament_extruder_id]==0.25}0.18{elsif nozzle_diameter[filament_extruder_id]==0.3}0.1{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_z_hop_types": [
    "Slope Lift"
  ],
  "full_fan_speed_layer": [
    "5"
  ],
  "slow_down_layer_time": [
    "9"
  ],
  "fan_cooling_layer_time": [
    "25"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "80"
  ],
  "filament_retraction_length": [
    "0.8"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "20"
  ],
  "hot_plate_temp_initial_layer": [
    "85"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "setting_id": "GFSA04",
  "filament_id": "Prusament PETG @CORE One",
  "filament_notes": [
    ""
  ],
  "idle_temperature": [
    "130"
  ],
  "chamber_temperature": [
    "35"
  ],
  "compatible_printers": [
    "Prusa CORE One 0.25 nozzle",
    "Prusa CORE One 0.3 nozzle",
    "Prusa CORE One 0.4 nozzle",
    "Prusa CORE One 0.5 nozzle"
  ],
  "name": "Prusament PETG @CORE One"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:54